Jump to content

Sony mechanical watch

Stevelp
 Share

Recommended Posts

Stevelp Watch Enthusiast

Stevelp

Posted
Posted

Hi all!  Just thought I would share a project I'm finishing up that I thought was kind of interesting.  Hearing the name Sony I immediately think electronics, the last thing I would have thought of is a mechanical watch like this one.  After a service, new stem (in progress) and a little polywatch on the crystal I think it turned out to be a great looking watch.  Someone got a little ham fisted on the dial between the 5-6 markers and there's a little corrosion on the dial in the same area but that's alright.  Anyone have any info on the history of Sony with Seiko?

SONY2.jpg

SONY.jpg

  • Like 2
Link to comment
Share on other sites
JohnD WRT Addict

JohnD

Posted
Posted
46 minutes ago, Stevelp said:

Hi all!  Just thought I would share a project I'm finishing up that I thought was kind of interesting.  Hearing the name Sony I immediately think electronics, the last thing I would have thought of is a mechanical watch like this one.  After a service, new stem (in progress) and a little polywatch on the crystal I think it turned out to be a great looking watch.  Someone got a little ham fisted on the dial between the 5-6 markers and there's a little corrosion on the dial in the same area but that's alright.  Anyone have any info on the history of Sony with Seiko?

SONY2.jpg

SONY.jpg

Surely it's just a Seiko, supplied as a corporate piece for Sony?  The same as this 1977 4004 for Motorcraft....

0VLMgqU.jpg

Link to comment
Share on other sites
FLwatchguy73 Super WRT Addict

FLwatchguy73

Posted
Posted

The watch is likely to be either an employee service award, an employee performance award or a corporate promotional item. I would be dubious to the possibility of it being branded and marketed for public sale by Sony. Considering Sony's deep connection to electronics, I would think if they were to have released a watch, it would be electronic, quartz or digital. Judging by the age of your movement (late 60's to early 70's), those were in existence, but were not used here.

Link to comment
Share on other sites
  • 6 months later...
watchweasol Distinguished Member

watchweasol

Posted
Posted

A year or two back I was give a TANDEM watch for repair.   TANDEM was an American computer company, This one had two faces and in side were two Miyota 2035 movements again a promotional piece.  The Gentleman who's watch it was worked for TANDEM.

I have also had one from Barbour  of  ( wax jacket fame) again with a miyota 2035 movement. 

Link to comment
Share on other sites
  • 4 months later...
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Movement inserted from crytal side

      By oldhippy · Posted

      Before putting it back in the case I would fit the hands and use a pin vice on the stem to make sure the hands were in line. 
    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
×
×
  • Create New...