Jump to content

Bucket list repair job


Recommended Posts

I'm sure all of us have a watch that we have put off completing the repair. The "One day I'll get to it" watch.

It is usually a watch early in our career/hobby. The one that was beyond our abilities at that time. The one that required a special tool that we didn't have. The one that requires a replacement part that is as rare as "unicorn poo".

Amid the Covid 19 lockdown in so many countries, now is the best time to revisit these projects that we have put off for so long. :D

Link to comment
Share on other sites

I'll start off the 1st one.

This my Waltham 12s pocket watch. Beautiful white gold case. Fully jewelled.

I was a non working watch which I got for a bargain from ebay. I found that the mainspring was broken. I temporarily fixed it by annealing the end of the mainspring, drilling a hole for the catch and shaping it to fit the barrel arbor. It worked fine.

So I proceeded to clean it while I went to order a new mainspring for it. Somehow I got distracted and forgot it was still soaking in my ultrasound. By the time I remembered, the shellac from the pallet stones had disintegrated. :pulling-hair-out:

20200330_103537.jpg

20190930_160231.jpg

20191001_140809.jpg

Link to comment
Share on other sites

I bought and repaired an 1871 Elgin pocket watch only to drop it while doing the final reassembly and broke the balance! I was utterly heart broken! It is still sitting waiting for me to get back to it. When I do, I'll have to source a correct dial and hands and hour gears as I "borrowed" them to complete and even older 1869 Elgin that I still have.

20200330_123642.thumb.jpg.41b60974e210e5fb633a9bafe1153b03.jpg

Link to comment
Share on other sites

I had been waiting for ages to get a  Universal Geneve, and finally got a nice 40s vintage Cal 267.

It just need a little tweek to adjust the hairspring overcoil. I bought some Vetus tweezers with a very fine point - but they were quite hard to compress. I gave the overcoil the required tweek, and released the tweezers too soon ..... completely trashed the hairspring.

Still makes me squirm when I think of it.

Of course, hairsprings for these are like the proverbial "unicorn poo". The balance was only used on one other calibre. 

I have a permanent watch on ebay ..... one day.

20181024_133205.thumb.jpg.cc6b8366f21b03db6ccee045c9bda374.jpg

Link to comment
Share on other sites

I bought some Vetus tweezers a while back and also found them hard to compress so went back to my old cheapies. I also bought to do HS but didn,t risk it fortunately, else I might have been in same boat.  HS not my forte at the best of times !!

Link to comment
Share on other sites

Actually, I have procured all the necessary tools and materials to re-shellac the pallet jewels. Read up and watched many videos on escapements.

Probably the only reason for my procrastination is that after many failed attempts, during my moment of despair I prayed to God that he not let me leave this earth till I finished this job. :startle:

20200330_234930.jpg

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I wish they would have done so in this case. The whole story went like this: I sent my speedmaster to an omega service center about 10 years ago (at that point of time I haven't even started watchmaking). After the watch came back to me it had only about 6 months wristtime until january 2024 (not fair for this nice watch but the other pieces of my collection want wristtime too 🙂). So my conclusion is that the barrel was already faulty when it came back from service, can't imagine that amount of wear in 6 months wristtime. In january 2024 the performance on the wrist was quite bad, so I decided to have a look by myself. I have to admit that I didn't check the barrel close enough as I thought it must be ok, couldn't have issues after official omega service. That was a mistake, I will learn from that. Follow the golden rule: Nothing is certain except death and taxes.
    • I am same as you oldhippy I won’t touch anything with a battery, I keep getting requests to but I just say I only do mechanical clocks, there are quite a few errors & omissions with the repair guide have a look at this. https://mb.nawcc.org/wiki/Encyclopedia-Subjects/Torsion-Clocks/Book:Horolovar-400-Day-Clock-Repair-Guide-10th-Edition-Errors-and-Updates
    • Nice experiment. As it will be no problem, please put a twice less mass (half of the two penies) and read the amplitude, will be interesting. I mean to determine what is the relation torque/amplitude.
    • parts touching that aren't supposed to touch definitely would cause an issue. there not supposed to be touching there supposed to be independent which means that @VWatchie is correct that the ratchet wheel has no effect on performance. so if the ratchet wheel in your particular case is touching that is definitely going to be an issue and needs to be addressed. did you know that the Swatch group service centers do not change mainsprings? Swatch group service centers have an infinite supply of spare parts so they just change the mainspring barrel the whole thing. Plus anything else the watchmaker doesn't like just gets replaced like anything related to the escapement they just replace the components because they can.
    • The pivots look OK. In this position, balance may rub on the pallet bridge, the roller table may rubb on the pallet fork, the bottom of roller table may rubb on the main plate, and on the tip of the screw that fixes the bottom endstone plate, the impulse jewel may rubb on guard pin, the rounded part of the pivot may rubb on the hole jewe too. Thiss all may be due to broken, missing or moved down endstone, or the plate with the stone has some dirt or other obsticle under it. But, sometimes different odd reasons can exist, like for example someone has changed the balance from a donnor movement. All the reasons are visible and must be checked. For beginning, remove the lever and it's bridge and do the free oscillations test.
×
×
  • Create New...