Jump to content

Timex M25 date wheel


Recommended Posts

Well, while on lock-down I woke up this morning with good intentions of oiling up an old Timex marlin i wear from time to time. After my recent success stripping and servicing a 6309a I figured that oiling the old "disposable" movement wouldn't be to tricky. I followed the service manual barring removal of the balance because I am still a little scared of going near hairsprings, put the dial back on and was bending the last dial foot back into place when my tool slipped and went right into the movement, snapping the pallet fork clean in half. I went from feeling pretty pleased with myself to devastated instantly.

I had a donor in my toolbox minus a balance assembly. Feeling like I had no choice I set about changing the balance over and spent about 45 mins fighting with the loose end of the hairspring and wedge pin which is like threading a needle with your eyes closed, at least for a total beginner like me. After a few hours I managed to get it fitted and running well.

 The only thing that's stumping me now for some reason is the date wheel of all things, it just doesn't seem to be holding into place with the assembly. After the day I have had it can sit on the bench until the morning . 

Any techniques out there that people use gratefully received ?

If nothing else it will give the more experienced a good old laugh during these sobering times.

Hope you are all safe and well

Thanks

Dave 

 

 

 

It had once belonged to my late grandfather but wasnt exactly an heirloom  as it came to me needing a set lever, a new stem and a strap.. I got it working last year and wear it 

  • Like 1
Link to comment
Share on other sites

Hi Dave   Not too familiar with the 25 but usually there are locaters which guide the day/date wheels, either one or both are screwed to the plate,  Is yours floating, if so it mabe relies on the dial and its washer to apply the pressure to hold it down.

Hopefully our Timex Guru JerseyMo will pick up on this or alternativly PM him. Cheers

Link to comment
Share on other sites

So, as it turns out I was pretty tired last night after working on the watch for the better part of the day.

(Apologies for the random sentence at the bottom)

That being said I hope you can forgive me for putting the date wheel on in the wrong order ... :wacko:

I took a look at the service manual over breakfast and noticed straight away, ran through and fitted it without too much issue.

I got it put back together but the second hand seems a bit bent and is now catching on the minute hand now .. typical.  

Whenever I work on watches I always learn way more than I bargained for, like having to fit a new balance and feed the hairspring through the regulator slot and wedging into place.

Most of it is due to inexperience but I do enjoy the process, retrospectively ...:biggrin:

Cheers 

  • Like 1
Link to comment
Share on other sites

2 hours ago, watchweasol said:

Hi Dave   Not too familiar with the 25 but usually there are locaters which guide the day/date wheels, either one or both are screwed to the plate,  Is yours floating, if so it mabe relies on the dial and its washer to apply the pressure to hold it down.

Hopefully our Timex Guru JerseyMo will pick up on this or alternativly PM him. Cheers

pretty sure yours is as watchweasol has said, they are a pain at times to stay in place, well done with the hairspring, i started on timex watches so i know your trepidation. straightening a hand is reasonably straightforward, again just take your time.

  • Like 1
Link to comment
Share on other sites

Before bending hands make sure the hour and minute hands are installed correctly. I seem to recall needing to adjust the angle of one of my timex minute hands not long ago. Although I think I also fiddled with the hands for a half hour and finally gave up and bent the second hand very slightly :)

Link to comment
Share on other sites

  • 2 weeks later...

Hi guys, just a quick update

The donor movement doesn't seem to be holding up, the pin on the 4th wheel that runs up through the the canon pinion seems far too short, like it has been snapped and there just isn't enough on the end to hold the second hand. 

Also, the balance regulator is pretty bent which is forcing the hairspring onto an angle. 

Is it at all possible to take the plates apart, that way I might be able to replace the pallet fork on the old movement and then swap the balance back across?

Failing that ill be looking for a replacement M25 movement. :wacko:

 

Link to comment
Share on other sites

4 hours ago, Dave84 said:

Is it at all possible to take the plates apart, that way I might be able to replace the pallet fork on the old movement and then swap the balance back across?

 

Yes, the plates are held together by three screws.

 

Link to comment
Share on other sites

8 minutes ago, JerseyMo said:

Yes, the plates are held together by three screws.

 

Thank you, Is it like a can of worms when you open it up or is it a pretty straight forward  job ?

Link to comment
Share on other sites

3 minutes ago, JerseyMo said:

well its like holding on to petroleum jelly. 

Hahahahah great. Thinking about it, I could have a go at taking them apart because in their current states both movements I have are no good but if I manage to save the part I need I may be able to fix one, if not I will have to source another movement anyway :blink:

Link to comment
Share on other sites

3 minutes ago, Dave84 said:

Hahahahah great. Thinking about it, I could have a go at taking them apart because in their current states both movements I have are no good but if I manage to save the part I need I may be able to fix one, if not I will have to source another movement anyway :blink:

What is wrong with the original movement?

Link to comment
Share on other sites

8 minutes ago, Dave84 said:

I snapped the pallet fork with a rogue screwdriver as I was folding over the last dial tab ....:unsure:

the pallet fork is the most fragile of all the parts.  You should be able to swap them.

 

Link to comment
Share on other sites

3 minutes ago, JerseyMo said:

the pallet fork is the most fragile of all the parts.  You should be able to swap them.

 

I was frustrated with myself, I am usually very careful. There is also a certain amount of guilt because the watch belonged to my grandfather, typical. 

I  will attempt it tomorrow , fingers crossed I don't break anything else ... :biggrin:

Link to comment
Share on other sites

Well, there's no going back now.

I have taken both movements apart, removed the good pallet fork and sat it in place in the old movement.

I have offered up the dial side to clamp it back together several times now and have disturbed the wheels each time. I will keep trying but any tips  with lining it up will be very welcome :-)

IMG_20200408_163607.jpg

Link to comment
Share on other sites

I am afraid there is no magic wand with these movements just a great deal of care and patience. they are fiddly little things,    Like one of those puzzles where you have to get all the little balls in the holes. always one falls out.   best of luck.    cheers

  • Like 1
Link to comment
Share on other sites

23 minutes ago, watchweasol said:

I am afraid there is no magic wand with these movements just a great deal of care and patience. they are fiddly little things,    Like one of those puzzles where you have to get all the little balls in the holes. always one falls out.   best of luck.    cheers

I am sat here wondering if I could make a lowering platform of sorts with grips top & bottom that could keep the movements on a straight trajectory with each other. Got to be better than my unsteady hands :biggrin: 

Link to comment
Share on other sites

9 minutes ago, JerseyMo said:

have a look at this post - 

 

Thanks Mo 

I will refer to this and rebuild the movement in the same fashion as yourself , perhaps I will have more luck .

Link to comment
Share on other sites

Got on with the Timex this afternoon, replaced the pallet fork and added some photos of the process.

The Mrs has called "food" so I will have to call it for now. 

I feel pretty happy that I was able to put it back together but a big thanks to Mo for linking the above feed, it really helped. The service manual doesn't go as far as taking the framework apart so it was uncharted territory for me. I just hope it works ...

The pallet fork isn't lined up with the balance yet, but that's the final task to see if it springs to life. 

 

IMG_20200409_163316.jpg

IMG_20200409_163359.jpg

IMG_20200409_163505.jpg

IMG_20200409_163536.jpg

IMG_20200409_163634.jpg

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
    • Does anyone knows what size case a need for a dial diameter 20.60mm?
    • Sounds like the story with my Rolex. Poor (expensive) job done by an official Rolex dealer with an "in-house" watchmaker, hence I learned watchrepair and did the servicing myself. Same story as I learned with the Omega 861, again poor job by an "in-house" watchmaker by an official Omega dealer. Once your watch goes through that back-door, you have no idea what is going to happening to it 🫣   Quite nice that they sent back the parts which had been replaced !
    • yes that's definitely not right at all. I have a picture one of my friends has a Omega coaxial there was having issues to lose asking me where he should send it. As that's a specialty watch I suggested the service center. When he got it back he sent me a picture so the replace the dial as you can see the hands the mainspring barrel and I think the price was really quite decent considering all the stuff they can replace. So I do know they do change the barrels but the other person I worked at the service center when I would ask questions and unfortunately I can't remember all the answers. I think a lot of the changing a parts is at the discretion of the watchmaker. Plus I don't know enough about the chronographs and whether that would be considered a vintage watch? I take some of the vintage watches may have been sent directly to Switzerland or another service center. Obviously with a watch like the one down below they probably have a infinite supply of parts is its relatively modern vintage stuff becomes more interesting even the watch companies don't have necessarily infinite supply of parts. But no matter what the watch shouldn't disintegrated six months that's definitely an issue.        
×
×
  • Create New...