Jump to content

Need to know if it's genuine or not

taimoorshah7
 Share

Recommended Posts

oldhippy Distinguished Member

oldhippy

Posted
Posted

Its a job to tell without seeing the movement, there are so many good fakes around these day. One thing that puts me off, the bracelet looks a little rough in the open position. Ask the seller for a photo of the movement in the case.  

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, taimoorshah7 said:

I want to buy this watch but I don't know if it's genuine or not can someone kindly guide me ?

Beside the good answer above, I note that you've joined this forum -which is dedicated to repair discussion- only to ask this.


A better place would have been a collector's forum like Watchuseek or Omega. Or perhaps you have done that already too.

  • Like 2
  • Thanks 1
Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi    I have checked the serial number on two sites both come up with a manufacturing date of 1998. As Old Hippy says its difficult to say without getting you hands on it. as said get more pictures, crown top, the clasp(should have omega stamp). Price wise I genuine there or thereabouts, But need further checks as jdm said look at the omega forums and ask questions.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Good job, that band matches the watch perfectly.
×
×
  • Create New...