Jump to content

Seiko SARB033 wobbly hands when crown pulled out

N3FSD

By N3FSD
in Introduce Yourself Here

 Share

Recommended Posts

N3FSD New Member

N3FSD

Posted
Posted

Hello everyone, I have recently been caught up in the Seiko SARB033 frenzy and bought one direct from Japan with Japan only warranty. The watch is perfect and exactly how I expected it to be, however when I pulled the crown out to change the time I noticed a worrying amount of play/wobble in the hands as if they are loose. The watch keeps good time, well within spec. I was told that the movement is loose and that the movement clamps need tightening. Could there be another reason for this problem as I see no moving of the movement through the display back. Any help will be much appreciated. 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

That is excessive and strange play, possibly a lose cannon pinion. It doesn't seem that the entire mov't is moving by looking at the date, which doesn't move. Either have it inspected by a reputable watchmaker or return it to the seller. If they raise any objection just open a claim with PayPal or the CC issuer and let them handle. 

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, Nucejoe said:

Fault at center hole, cuz seconds arbour moves too. If the is a center jewel ! Then broken otherwise excessive wear at center hole. 

I agree with that. But it can't be wear since it's a new watch. I'd be curious to see a timegrapher picture.

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
    • doober
      Rado rotor removal

      By doober · Posted

      Hi! I am in the process of restoring a rado captain cook mkII. I want to remove the rotor, but I am not sure how to and need some help. As you can hopefully see on the photo there are 2 screws. The left one has two positions, the right one looks like a regular screw. I have tried turning the right one, but it does not give even after using more force than I would expect. Anyone know the function of the left screw with the two positions and how to remove the rotor? Thanks!!
    • Randy55
      Introduction

      By Randy55 · Posted

      Welcome to the group Stirky. You can search for just about every subject in the craft here. Don't be afraid to ask if you can't find the answer that may have already been covered ( some ad nauseum LOL ). You don't have to buy Bergeon to get good quality. There are many decent mid-range tools available that will last you a lifetime. Cousins would be a good place to start . Cheers from across the pond ! Randy
×
×
  • Create New...