Jump to content

Winding Stem Holding Screw Has A Stripped Thread

WillFly

By WillFly
in Watch Repairs Help & Advice

 Share

Recommended Posts

WillFly Distinguished Member

WillFly

Posted
Posted

I've acquired an old and very worn Tiresa head (Swiss, 17 jewels) to play around with - broken mainspring, etc. - and I'm having some trouble in undoing the screw that holds the winding stem. It turns freely - but doesn't actually unscrew - so the thread is probably mangled - and there isn't enough purchase for tweezers to grip it. Minor, but damned irritating! Unfortunately, it's not so loose that it will just drop out. Any ideas here?

 

post-64-0-83693500-1421659372_thumb.jpg

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted (edited)

Will you will have to use rodico perhaps or a touch of super glue on the end of a pokie thing & hopefully it will lift it out. The only other thing I can think of is if there is no power in the watch is to remove the the bridge wheels etc and hopfully you can access the stem from this side & wiggle it out.

Edited by clockboy
Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted (edited)

It could have a shoulder on it that holds it captive until you split the movement. I've come across that sort of thing before.

It's just a thought Will.

I've also seen them where you unscrew a couple of turns and then press the end of the screw to release the stem.

Edited by Geo
Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

Will had another thought!!!!

The screw has most likely detached itself from the retaining yoke that stps the stem coming out. What might work is to remove the movement retaining ring & have the watch dial up & wiggle it & at the same time pull the stem. Be careful as the stem can brake

Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
  • Author
Posted

No, alas, I've had to put it on one side, just for the moment, as I've been chauffeuring various family members hither and thither and doing other domesticities. Grandkids school runs, mother-in-law (who's 88 and frail) to hospital for a test this afternoon, shopping tomorrow morning, hospital myself on Friday morning (suspect mole on back). All sorts of fun and games, and I like to book myself some tranquil play space!

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted (edited)

No, alas, I've had to put it on one side, just for the moment, as I've been chauffeuring various family members hither and thither and doing other domesticities. Grandkids school runs, mother-in-law (who's 88 and frail) to hospital for a test this afternoon, shopping tomorrow morning, hospital myself on Friday morning (suspect mole on back). All sorts of fun and games, and I like to book myself some tranquil play space!

Me & you seem to have the same hectic life Will. Me clearing a loft with 30years of crap in it. Grandson for the next two days etc etc. PS you might appreciate this in the loft found a box of my old LP,s + my faithful Thorens turntable, sadly with the counter balance weight is missing. All this and them watches still need looking at!!!

Edited by clockboy
Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
  • Author
Posted

I'm hoping to get a "window of opportunity" to sit down with it this weekend. The grandkids and the local health centre have been taking up the week, and I've got to sort out 3,000 pieces of sheet music into a filing cabinet I collected from an eBay seller on Monday afternoon, and I can't get the cabinet into the garage until I've shifted amps and crates out of the way, and then I've got to get my son over to give me a hand with shifting the cabinet, and then... and then...

 

So I'm a bit busy at the moment! :D

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Modular Movement Holder.pdf  
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Good job, that band matches the watch perfectly.
×
×
  • Create New...