Jump to content

Rolex Submariner Case Opening Issue


clockboy

Recommended Posts

Have problems opening my Rolex submariner case back. It has never been opened before so I think the issue is just very tight. Removed the bezel to clean and it was really,really dirty so I expect this is the issue with the back. I have been trying to open with a opener made by Huaxing but it will not budge and eventually the die slips. I don,t want to do any damage but I don,t know if the die is just a bad fit as it is not a Bergeon or if I need a more substantial opener any one with advise will be most appreciated. 

 

post-234-0-44703100-1421323630_thumb.jpg

Link to comment
Share on other sites

I have one of these myself and it's served me well. Have you tried gripping the case across the points of the lugs in fibre vice soft jaws to allow you to exert maximum downward pressure while applying torque? I had to do that with a Tudor Oyster that didn't want to open.

Link to comment
Share on other sites

Thanks Geo, to get a really good purchase I removed the bezel inserted the watch into a watch case holder. However I put downward pressure before twisting with a lot of pressure (more than I like) but no good and eventually the die slips. I was just wondering if the bergeon die is a tighter fit or I need different style of remover. The Bezel was really tight even with a Bezel remover and the dirt under it was substantial so I guess this is the issue. 

I just do not like forcing for fear of damage.

Edited by clockboy
Link to comment
Share on other sites

I also have a set of the cloned Bergeon dies and some are OK and some slip - even when I use them in the bergeon bench case opener. 

 

I purchased some Horotec dies (which also fit the Bergeon case opener by the way) and never had a problem since.

 

Do you have a glass lifter (the type with all the prongs)? If so, you can try tightening it round the back and turn. Sometimes works.

Link to comment
Share on other sites

Thanks Mark, I have a glass lifter (prong type)& will give that a try. If no good I will look at Horotec dies perhaps. I presume I can get them in Cousins. I just have a feeling to shift its going to require a pro type tool.

Link to comment
Share on other sites

Could be time for the supa glue and a 19mm nut!!.. :startle: ....its never failed me......then tighten back up with the die if you can. A few weeks back I did just that on my Breitling asI wasn't going to spend £50 for a die and it worked fine. I have the same set of dies you have and they worked fine on my Sub but it had been serviced before so not on as tight as I expected.

Edited by ash145
Link to comment
Share on other sites

Absolutely it will. That, and it's Bergeon (5700, my one) brother are extremely good tools. The good thing is you will get dies for Rolex, Panerai, Baume & Mercier and Breitling to fit. If you have the budget, its a no-brainer.

Link to comment
Share on other sites

I'm sorry I'm late for this thread! (clockboy just pressed the button!) but the opener Geo recommends is excellent, (I just got one for Christmas) if it is the original LG. The down side is they only come with the Rolex dice! In any case, I also got a Witschi opener that accepts Horotec and Bergeon parts!

 

It is here: http://www.ofrei.com/page557.html#27092

 

Cheers,

 

Bob

Link to comment
Share on other sites

I have a set exactly the same Chinese back opener set that Clockboy was using and it's worked very well with both my vintage Rolex and Tudor. The only case it wouldn't open so far was a Chinese copy Rolex.

Edited by Geo
Link to comment
Share on other sites

New toy arrived added pic. Opening the rolex case with the Horotec was simple with no effort.  

Conversation "whats that dear"  ------ "Oh just a tool for my watches" ---- "how much "  ,

"no nothing really, only a few quid dear "  :D

 

 

post-234-0-52280800-1421680616_thumb.jpg

 

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • 🤔 leaving the EU meant that UK was no longer part of the convention and have already been turned down an independent reapplication. I'm pretty sure courts have to be held in Switzerland in this case. There will be a lot more watches stashed away in draws  tbh, folk wont be able to afford to maintain them. Cheap watches will be bought and top end watches by folk with plenty of cash that can pay for service and repair. The expensive once in a lifetime gifts and everything else inbetween will be at the forgotton when they stop working. I know i was being a numpty, get used to it 😄
    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
×
×
  • Create New...