Jump to content

Veteran Jeweler

RoyalDiadem

By RoyalDiadem
in Introduce Yourself Here

 Share

Recommended Posts

RoyalDiadem New Member

RoyalDiadem

Posted
Posted

Hi Folks! I'm a long time fine jeweler, benchman, manufacturer, setter, operations executive and well,... little i have not done. Operated my own store in our 21st year and 20 years with a corporate multi-store chain from management to VP Operations. oh,.. and Graduate Gemologist (GIA) Certified Gemologist Appraiser (AGS)...

www.royaldiadem.com

 

Sterling VanDerwerker CGA(AGS) GG(GIA)

SV2008.jpg

Link to comment
Share on other sites
ITProDad WRT Addict

ITProDad

Posted
Posted
Hi Folks! I'm a long time fine jeweler, benchman, manufacturer, setter, operations executive and well,... little i have not done. Operated my own store in our 21st year and 20 years with a corporate multi-store chain from management to VP Operations. oh,.. and Graduate Gemologist (GIA) Certified Gemologist Appraiser (AGS)...
www.royaldiadem.com
 
Sterling VanDerwerker CGA(AGS) GG(GIA)
SV2008.jpg.d5871402386da59c4ee17925e1360279.jpg

Welcome


Sent from my iPad using Tapatalk
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mikepilk
      Setting lever spring

      By mikepilk · Posted

      I would harden and temper (to a light blue). It's so easy to do and only takes a couple of minutes.
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      Here is the insert ring for rectangular or elliptical movements: Note that the length is the side with the stem cut out on the spreadsheet (in the picture below this is 15.15: Here is the fake pdf file, again you need to convert to .zip after download to access the FreeCAD and 3mf files. Rectangular insert disc.pdf    
    • JohnR725
      Omega cal. 565 - low amplitude

      By JohnR725 · Posted

      as you took the mainspring out what did it look like? It's amazing how much amplitude you can get if the mainspring actually has the proper shape. last week I was doing a 12 size Hamilton and was very much surprised with the beautiful back curvature the mainspring had. Then the watch had a really nice amplitude the group would be so proud it was 350 until I dropped the lift angle down to 38 that drop the amplitude quite a bit below 300. then with the beautiful back curve it still had really nice amplitude the next day. I really wish all my mainspring's look like this as the watch had beautiful amplitude the next day. So many of the aftermarket pocketwatch Springs I see now do not have anything resembling a back curve may be a slight curve and that's about all. They still work but they just don't work as nice as a properly made spring. then Omega as all sorts of nifty technical documentation unfortunately every single corner is watermarked with where it came from who downloaded it etc. very paranoid company. On the other hand I will snip out images like from the document on recycling a mainspring barrel. for instance here's the section on what your mainspring should look like. water damaged a lot of times means rust was there rust on this watch?
    • RichardHarris123
      Without Our Forum

      By RichardHarris123 · Posted

      I wondered that?
    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      I dont understand why a patreon membership would have limited places ??
×
×
  • Create New...