Jump to content

Bent mainplate

Omegajeff

By Omegajeff
in Watch Repairs Help & Advice

 Share

Recommended Posts

Omegajeff Member

Omegajeff

Posted
Posted

Hello all. I am new to the talk. I’ve been watching the videos for about a year now and look forward to new projects. With that I recently began restoring my first watch. I purchased an Omega 563 movement. I failed to realize the mainplate had a slight bend that caused it to contact the balance wheel. Is it possible to straighten the plate after disassembly?

Link to comment
Share on other sites
saswatch88 WRT Addict

saswatch88

Posted
Posted

Are you sure the balance wheel or staff is not bent? I just cant see any circumstance which would bend a main plate, not saying it cant happen but i would think it would have to be deliberate. Maybe previous owner tried to repair and had fit of rage and slam dunked it on the floor.

  • Like 1
Link to comment
Share on other sites
yankeedog Distinguished Member

yankeedog

Posted
Posted

While anything is possible , I also think it unlikely. I would be much more likely to suspect wear in the hairspring assembly. I think that "debending " a main plate could be very tricky, because it would have to be done in a very precise manner.you would have to locate the exact spot and the exact amount of bend.unless you had some type of die made for this purpose you could make it worse,have you checked to see if the watch will run in different positions? does gravity have an effect?

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted (edited)

Can you post a few pics? I agree a bent mainplate would be a new one on me and I have a couple of decades at the bench. That's a really fine movement and while robust in use rather delicate to work on, not one I'd recommend as a first watch.

Edited by nickelsilver
  • Like 1
Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi I would agree wit all the comments so far, to bend the main plate would take quite a bit of force and to straighten it out would weaken the plate, But like has already been mentioned what else has been distorted/broken/bent.  As requested by Nicklesilver post some pics and one of the bent plate with a steel rule to acertain the distortion.

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted (edited)

If you place the plate on a perfectly straight edge, and see if you can see light through the gap between the edge and the plate, you should be able to figure out if it is bent. Check across various different directions. A bent plate would almost certainly result in damage to other components. A bent gear on the other hand might give the impression of being straight, but the illusion that the adjacent plate was bent. 

I think we need some good close up pictures to see what is going on.

Edited by AndyHull
Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted
3 minutes ago, rodabod said:

More likely to be a bent cock if anything. Ooh err. 

Could be, sounds painful... or maybe  misalignment of screws or pegs, leading to one side being pushed up and the opposite side down. 
Pictures.. we need pictures...

Link to comment
Share on other sites
ITProDad WRT Addict

ITProDad

Posted
Posted
Hello all. I am new to the talk. I’ve been watching the videos for about a year now and look forward to new projects. With that I recently began restoring my first watch. I purchased an Omega 563 movement. I failed to realize the mainplate had a slight bend that caused it to contact the balance wheel. Is it possible to straighten the plate after disassembly?

Anything is possible. Be sure it is bent and not being kept out of true by a piece of odd debris or possibly some other cause.

Be careful and prepared for it to break, as a worst case scenario. Take before and after pics to share, please.

Good luck.


Sent from my iPad using Tapatalk
Link to comment
Share on other sites
saswatch88 WRT Addict

saswatch88

Posted
Posted
12 hours ago, Omegajeff said:

I can see the bend. It is very slight but  enough that it is contacting the balance wheel and causing the rotor to not fully spin without binding. I will try and post some pics later tonight. Thanks for the feedback 

The balance has a decent about of clearance from the plate and if it is making contact then the bend has to be right at the edge of the movement. Which still blows my mind how it can occur, not to mention if there was something forceful enough to do that then i cant imagine how nothing else is damaged. I would really love to see a pic of this movement. It should be in some kind of medical journal for watches.

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted (edited)

Ouch.. I'm not sure if you will be able to straighten that without risking snapping it. Small gentle tapppity tap taps. 
If it were something less fragile, I would suggest heating it before bending, but in this case.. probably not..

Any suggestions anybody?
Put it in a vice between two soft jaws maybe?

I guess just enough unbending to stop the balance rubbing, then test, if still not satisfactory, then just a little more.

Edited by AndyHull
Link to comment
Share on other sites
yankeedog Distinguished Member

yankeedog

Posted
Posted (edited)

Ok...here is my blasphemy....the plate is buggered.. it  may or may not snap back. It may snap  off! It might  cause  more damage  and make the  watch inoperable  all together.  Option  one replace  the main plate ,this would be preferred..option  two..attempt  to straighten  bend..option three relive the plate of the damaged  area..take a file to it.very judiciously  file away the distorted  area. The balance  wheel  will turn and the watch  should  work. This of course  should  be your last ditch  option. The absolute  last resort.. but  in my opinion  if you really  want  to put that  watch back into service  ,it is something  you may want to consider. 

Edited by yankeedog
Link to comment
Share on other sites
Omegajeff Member

Omegajeff

Posted
  • Author
Posted

I was able to put it in a vice and straighten a good portion of it. The balance moves freely now and the rotor spins. To my dismay the wheels were not turning. I found the fourth wheel seized in the bridge. When I tried to remove it, snapped clean off. 

Link to comment
Share on other sites
Omegajeff Member

Omegajeff

Posted
  • Author
Posted

I checked the wheels before straightening and they did not move. At that point I figured, just do it and inspect later. All other wheels move freely. I ordered a new 4th wheel and am working on getting the pin out of the bridge. I am also stumped with the dial on this watch. Seems to have an old steam crane logo on the bottom. Haven’t been able to find any information. Looking through the loop it doesn’t appear to be added later on. Smooth on the dial. 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rossjackson01
      Intro

      By rossjackson01 · Posted

      Welcome my friend. 
    • rossjackson01
      Help please.

      By rossjackson01 · Posted

      Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
×
×
  • Create New...