Jump to content

Information Required On Mystery Omega 501 Movement.

Geo

By Geo
in Watch Repairs Help & Advice

 Share

Recommended Posts

Geo Distinguished Member

Geo

Posted
Posted

Hi guys, a few years back I purchased a new old stock replacement movement to fit into an old Seamaster. It certainly looks genuine and perfect, but there is no serial number on it.

Could someone please explain the absence of the number?

imagejpg1-22.jpg

imagejpg2-4.jpg

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted (edited)

Hi Geo,

 

Apart from this http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&&2uswk&Omega_501 which I believe you've already seen, I came up with this http://watchguy.co.uk/service-omega-seamaster-calibre-501/  They have this pdf I downloaded here for your -- and other interested members convenience:

 

movement3.pdf

 

I hope it is of some help in your quest!

 

Cheers,

 

Bob

 

PS. I don't know if this one is of any help: http://www.chronomaddox.com/OmegaCaliberList.html

Edited by bobm12
Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
  • Author
Posted

The autowinding bridge could have been replaced by a new one sometime in the past..?

Anil

Thanks Anil.

It's a possibility, but the the colour of the plating matches perfectly and everything looks brand new.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
  • Author
Posted

Here;s my guess.

COSC spec movements have to have a serial number. If this is not one of the COSC spec 501's then that might be your answer.

Interesting Jaycey.

I thought all movements would have a serial number issued by Omega, even replacements.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
  • Author
Posted

Thanks Marc, that was an interesting read and a mega project that the fellow carried out. It's certainly given me more food for thought.

The one thing that really confuses me, is I read a post on another Omega forum where a technician that worked for Omega said all movements were numbered. Maybe this one have been assembled from parts as your link suggests, but I may never know.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Is this a 'hack' ?

      By oldhippy · Posted

      I need to see photos of the whole movement before I comment. 
    • swiss2k
      Omega cal. 565 - low amplitude

      By swiss2k · Posted

      Hi @Jon, so, from one extreme to another the beat error is 0.1(min.pos) to 0.2(msx.pos), and as you mentioned the rate does up and down dramatically. Also checked the position of the collet, and the collet is not central to the jewel on the balance cock. Balance moves freely, per my understanding.   So, after 24h the ampl. fell down by approx 20 deg, which I would assume is expected. After adjusting the endshake I believe I gained around +10 deg. of balance movement. Which is great, and overall the balance is not at 220'ish deg.   What I did next, some might think is non-orthodox, but was wort a try. I too the mainspring out, checked again for endshake and if the pin moves freely, and cleaned everything. Usually when installing the mainspring I would use some barrel grease on the barrel walls, install the spring and put a 2-3 drops of D-5 oil on top of the wounded spring and in the places where the arbor sits. This time I took the spring and applied a ultra this coat of Molykote Dx paste on the whole spring, before installing it in to the barrel, and added some oil to the arbor as usual.  The result improved, at a full wound the balance produces about 230-237 deg. @JohnR725 I'm getting closer to 300 😃   What I am noticing, there is a fluctuation in amplitude. With time it would rise and drop about total 8-10 deg in an interval about 2 minutes. I assumed this ruled out the power transfer from the barrel itself. So I took the gear train out, cleaned and lubed. 
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
×
×
  • Create New...