Jump to content

Cartier Ballon Bleu - did I get a lemon?


Recommended Posts

Hi all - I am new here but would deeply appreciate any advice from the group.

July 2013 - I bought a Cartier Ballon Bleu men's watch.

In August 2013, within a month of buying the watch, I swam in a swimming pool with the watch and water immediately showed up under the crystal.  I took the watch in to Cartier for repair.  They did a "full service" on it and said it was okay.

Since that initial issue with the water, I have been super wary of getting into water with it and almost never do so.  I may have done it a time or two per year in swimming pools or freshwater.  A few weeks ago, I was in the ocean with the watch for about 5 minutes.  The watch may have been submerged by a foot or two, but I certainly did not go diving.  Almost immediately the watch stopped running.

I took it in to Cartier, and they are recommending a full service plus the replacement of the movement, hands, dial, and casing ring due to oxidation.

I find it nearly impossible to believe that a 6-year old watch could suffer so badly from oxidation that it would need this much replacement.  My hypothesis is that the watch is a lemon to start with, the repairs weren't done properly, or both.

However, I don't really know anything about such fine watches and would like to get input from folks who really know about these things.  I'd be grateful for any advice.  If you need more information, please let me know.

Thanks to all!

Link to comment
Share on other sites

My opinion is that is owner caused damage. A dress watch like your should not ever contact water, let alone enter a pool or sea with it.

There are many variations of this watch, some are quartz some are not but all are valuable. You can certainly give it to a reputable watchmaker for an alternative repair estimate, but if there are parts that he can't obtain you will have no alterative than the official service center. Note however that "full service" and "movement replacement" are mutually exclusive. You can also evaluate the level of oxidation on dial and hands by yourself using a loupe or eyeglass.

Edited by jdm
Link to comment
Share on other sites

Thank you for the opinion. I agree that, going forward, I will not have it touch water. Better safe than sorry.

But, if the watches should never ever touch water, why would Cartier state the below about its watches on the website and advertise them as water resistant to 30 m?

The water-resistance of your watch is ensured by sealed gaskets. The water-resistance seals of your certified water-resistant watch undergo natural deterioration due to aging. You are recommended to have a regular water-resistance check performed. This diagnostic service is provided at no charge by our expert watchmakers. Before any contact with water, ensure that the crown of your watch is fully pushed into the case so it remains water-resistant. When your watch is underwater do not activate the chronograph function, second time zone, or other secondary mechanical features. After swimming, make sure to rinse your water-resistant watch in clean water so as to neutralize the harmful effects of seawater or chlorine.

Link to comment
Share on other sites

Hi  when you bought the watch did it come with the user guide etc, and did you read it. It may be that the watch is only water resistant which implies an odd shower of rain or two ok but not in any way submersible. I have just read your reply to jdm's comment and indeed it is so. Not having a screw down crown with seal renders it likley to leak if submerged.   lesson learnt.  Only if its designated a diving watch and denoted waterproof should one swim with it remembering to have the seals checked regular and it pressure tested.

Link to comment
Share on other sites

2 minutes ago, baird1025 said:

But, if the watches should never ever touch water, why would Cartier state the below about its watches on the website and advertise them as water resistant to 30 m?

That is just an indication, unfortunately it's always exaggerated. 30m means in practice just safe to wash hands while wearing it. 

  • Like 1
Link to comment
Share on other sites

Crazy........my 20 dollar timex has better water resistence than that 10k watch. Whats the documented water resistence??? If youre not exceeding that then you shouldnt even have to think about much less be "weary". Id be curious to see what the OEM has to say. Not to knock you but this is just the reason why I haggle with the over priced watch game. Its such a racket.

Sent from my SM-G950U using Tapatalk

Link to comment
Share on other sites

Hi @baird1025 - I feel bad for you on such a nice watch. I don't think you've been unreasonable as a general consumer reading in effect "this watch is water resitant to 30m" and thinking you can take into water of less than this (probably not even 1m!) and thinking everything will be okay. Unfortunately this kind of marketing hyperbole is a sweeping statement for the Cartier range so is not really worth anything for a particular watch in their range. As already stated, unless a watch says it is waterproof it should never be deliberately taken into water. Waterresistant is merely a term to describe some effort to prevent water ingress in the event of an accidental splash etc.

Where can water ingress? The front seal (crystal); the rear seal (case back) and crown. If a watch isn't designed to prevent ingress by these means (=waterproof) then every watch will be different in its capability. What I'm getting to is that you haven't bought a lemon; it's just that the watch wasn't intentend for how you've used it. Even if you went to Cartier and tried to make an argument they would cite natural deterioration of the seals since you last had a service. 

If, in very simple terms, we consider a watch to be the case, movement, dial, hands and bracelet then Cartier are suggesting you pretty much replace most of the watch to bring it back to perfect. Ouch! This then ends up being a very personal decision on how, and how far, you want to proceed. What would be interesting though is if you could post a few pics to show the oxidation you're talking about.

 

  • Like 1
Link to comment
Share on other sites

On 1/9/2020 at 3:16 AM, baird1025 said:

In August 2013, within a month of buying the watch, I swam in a swimming pool with the watch and water immediately showed up under the crystal.  I took the watch in to Cartier for repair.  They did a "full service" on it and said it was okay.

That already sounds crazy to me. Such a high end watch surely would be pressure tested to 3 ATM at the factory and should survive some swimming.. Would vigorous swimming (i.e. slamming the watch in the water each stroke) locally exceed 3 ATM of pressure?

For seals to degrade in 6 years to allow ingress of ocean water at 1ft is also pretty crappy..

Link to comment
Share on other sites

And to add to my comments there of course isn't standardisation. The crown area for water ingress is probably the weakest spot. I have various watches and if we take the ones that aren't waterproof - so they can only say they are water resistant - I have one with a screw down crown; one with a double gasket set-up and another with a single gasket etc. So not all watches are born equal in their water resistance capability ... and the original cost of a watch isn't any guarantee of its superiority in this area as we know from some of the incredulous comments in this thread! 

Given the cost Cartier are now saying it will take to put everything right after a dip in water I think it is worth @baird1025 making a case. But rather than going to Cartier direct (who aren't ever going to admit a liability) maybe take to an independent to for an assessment report. This might go some way to help even if there was a compromise and an agreement by Cartier to make a discount for the work. Just an idea...?

Link to comment
Share on other sites

Thank you all for the input.  May I share the denouement...

So, I told Cartier - very politely - that I was disappointed in the performance of the water-resistant watch.  They conferred internally and called me back a few days later. They offered to offer complementary replacement of the hands, dial, and casing ring.  They had been asking roughly $500 for this set of repairs.  They said that I should pay for the full service (at, again, roughly $500), which they say should be done every 4-5 years.

I found this offer agreeable and accepted it.

And I will never allow the watch to touch water again.

Thanks again, everybody!

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • Never and others. Yes like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
    • Get someone local to tig it ,very easy fix and should only take a few minutes so probably wouldn’t cost much ,or failing that get it very clean and silver solder it. Dell
    • Hi, The winding pin is not split, well that's how it was when I obtained the watch. The movement is front-loaded and here's a picture of where the case screws are fitted. The face picture is before I dismantled it. Quick update.  I've always had a nylon ring sitting in the parts try that I wasn't sure where it went and left it to the last thing as I know it must be part of the case assembly. Anyway, looking at the picture in my last post you can see, just under the winding stem, a white-looking object, this is the nylon ring 🤭 So, I had to remove the dial again and replace the ring. Once this was all back together I placed the movement in the case and realized my initial problem maybe is not a problem as it looks like I can screw the movement back in the case and then place the hands as the dial is nearly flush with the outside of the case anyway so I'll be able to check for alignment. if all is good then just fit the crystal and bezel 🤔 I can't think of any issues with this approach but please comment if you think I've not thought of something. Another lesson learned as well. Take more pictures not just of the movement parts and location 😅
×
×
  • Create New...