Jump to content

Breitling Movement.

markr

By markr
in Watch Repairs Help & Advice

 Share

Recommended Posts

markr Super WRT Addict

markr

Posted
Posted

I found this in a box of stuff.  Since the movement does not have the Breitling name on it I'm assuming it's not a Breitling movement and that the dial is also fake.  Can someone tell me if the dial and movement are from Breitling?  What movement is it?  Is the movement a good movement and should I build a watch around it?  I'm interested in your advice on what to do with it. Thanks

IMG_2980.JPG

IMG_2979.JPG

IMG_2978.JPG

IMG_2977.JPG

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

Seems to me a good occasion to practice on that mov't. Learning from it will be worth the time spent, and any improvement on the timegrapher picture a reason for building pride and self-confidence.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchrepairIRE
      Crown Snapped Off - Armani Renato Watch

      By watchrepairIRE · Posted

      Thanks again for all the help. I found a number on the movement (715) after much searching. I guess it's the below movement so I will order than and see how I get on. https://www.ronda.ch/en/productfinder/caliber/715
    • watchweasol
      Casio AQ-321G Battery

      By watchweasol · Posted

      Hi. Thing to do is measure the battery space.  Diameter.  X depth ..    I have seen it listed as  sr626sw.  377 measure to check then check the dimensions of the 377.    
    • DouglasSkinner
      Hillabold's Pallet Setter

      By DouglasSkinner · Posted

      Hello!  Does anybody have this tool?  This is mine.  If you have one, does it look complete?  How do you use it.  (I have the instruction sheet but it's hard to read!)  thanks!
    • arron
      Ball PW balance staff and hands

      By arron · Posted

      @JohnR725 that's very helpful.  I appreciate the time you took to give those instructions and post the pictures.  below is a picture of my staff, which looks identical to the ones you posted.  The approx measurements I got are: .772 on the left part of the staff; .715 on the right side of the hub; the hub is 1.107; and the overall length (minus the broken pivot) is 5.248; which seem to line up with the measurements you posted.  I didn't think to measure the pivot, which I'll do if there's enough of one left on the staff.  Thanks again.
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      Thank you to both of you!  I've been somewhat derailed by this quandary for a couple of days now. I am guessing that the point of the wider tweezers is to support the whole spring at the same time in an effort to prevent it going under tension... I have already discovered the Zen of a clutter free space, and trying to keep my work well away from the edge, however the most terrifying of the flights wasn't so short, I had my work in the middle of the table and nothing else around.  That particular launch was towards me.  I distinctly recall feeling the spring hit my left hand as it escaped.  I only found it by dumb luck, on the floor, between the legs of my chair.  I need to order a pack of replacements just in case.  I think I recall a thread discussing where to find them, and the differences between the clones and the authentic ETA ones, pointing out that they're not interchangeable (the clones being longer IIRC).  Now I just have to find that thread again.  What I haven't mastered is the zen of the search function here.  I'm sure I"ll get that down eventually. So this is similar to, but different from one of the posts I had found in my original searches (or maybe I'm just hallucinating, I can't find the post I thought I remember).  The bits about the corner filled in a gap in what I'd read before.  At least I have a more clear picture in my head about what needs to happen now.  Yes, I've learned about how touchy these springs are.  What I'm not sure I have a good grasp on is the understanding of what causes the spring to flex, other than to say "the slightest little touch"  I think I'm going to try a small bit of Rodico to position the spring next time.
×
×
  • Create New...