Jump to content

Paul Garnier Chaff Cutter Escapement


wls1971

Recommended Posts

I have a wooden cased carriage clock dating from about 1840 fitted with a Paul Garnier "Chaff Cutter" Escapement, has anyone ever worked on or come across one of these it was a fore runner to the platform escapement, It runs but seem to have a arc of swing on the balance wheel of about 60 degrees is this correct for these escapements ?, it does run well and if the balance is gently stopped it springs back to life instantly once released, I have read that the action of the escapement is of a dead beat variety and is in some way related to a verge escapement but I can find very little on the web about them., It consists of two club toothed discs that make up the escape wheel, with a half circular disc with sloping edges on the staff, that releases and locks the opposing discs on the escape wheel as it swings.

If anyone has any info or knows of a site with any please let me know.IMG_2965.thumb.JPG.525b00e55339c868cffb6059d62d05e8.JPGIMG_2970.thumb.JPG.8661d605e6024bc5491b8da724477c6b.JPGIMG_2973.thumb.JPG.d7c3176dad8525a55e8b8b265163823c.JPG

Link to comment
Share on other sites

This was a variation of Debaufre's escapement, which was interrelated with several others all trying to deal with the massive recoil of the escape wheel in the verge escapement. There is a good description in Paul Chamberlain's It's About Time.  Like a cylinder or most any frictional rest escapement amplitude is normally quite low and you may find that there is a pin on the balance to prevent it going too high- though perhaps not on a stationary clock like this. One interesting thing with frictional rest escapements is they are somewhat self regulating regarding isochronism, as when power goes up the friction during the non-escape time goes up too, limiting the amplitude.

 

60 degrees seems a bit low, I would imagine about double that if everything is in good order and lubricated. But if it's working well it's not really a huge issue, the fact that it self starts right away is a very good sign.

 

There is a good chance there is some sort of adjustment for the depthing of the escape wheels to the impulse table on the staff; most verge escapements had this too. When one escape tooth has just "escaped" the following tooth should land on the flat surface of the impulse table. If it's landing on the sloped surface the depthing is too light.

Edited by nickelsilver
  • Like 1
Link to comment
Share on other sites

You don’t get much of a swing from the balance with this type of escapement; it is nothing like the swing of an anchor escapement. They are slow in comparison much like as you say a Verge. The ones I have worked on I think 3 or 4 after a proper O/H always seemed lazy in the rotation; it’s as if the balance wheel was too heavy for the hair spring. I don’t see much oil on the two club toothed discs, this might be to do with the photo. Not a very popular escapement, which might be due to its poor action.  

  • Like 1
Link to comment
Share on other sites

25 minutes ago, oldhippy said:

You don’t get much of a swing from the balance with this type of escapement; it is nothing like the swing of an anchor escapement. They are slow in comparison much like as you say a Verge. The ones I have worked on I think 3 or 4 after a proper O/H always seemed lazy in the rotation; it’s as if the balance wheel was too heavy for the hair spring. I don’t see much oil on the two club toothed discs, this might be to do with the photo. Not a very popular escapement, which might be due to its poor action.  

Yes as you say the action seems Lazy in comparison to a platform lever or cylinder escapement, they also seem to inhabit a short space of time in carriage clock production 1830-1850 , with platform escapements soon superseding them. I did oil the escape wheels but just a small drop of oil on one tooth on each , it has been running three days now but I have not measured time keeping performance yet but I should imagine it will run far short of a good platform escapement.

Link to comment
Share on other sites

5 hours ago, wls1971 said:

I have a wooden cased carriage clock dating from about 1840 fitted with a Paul Garnier "Chaff Cutter" Escapement, has anyone ever worked on or come across one of these it was a fore runner to the platform escapement, It runs but seem to have a arc of swing on the balance wheel of about 60 degrees is this correct for these escapements ?, it does run well and if the balance is gently stopped it springs back to life instantly once released, I have read that the action of the escapement is of a dead beat variety and is in some way related to a verge escapement but I can find very little on the web about them., It consists of two club toothed discs that make up the escape wheel, with a half circular disc with sloping edges on the staff, that releases and locks the opposing discs on the escape wheel as it swings.

If anyone has any info or knows of a site with any please let me know.IMG_2965.thumb.JPG.525b00e55339c868cffb6059d62d05e8.JPGIMG_2970.thumb.JPG.8661d605e6024bc5491b8da724477c6b.JPGIMG_2973.thumb.JPG.d7c3176dad8525a55e8b8b265163823c.JPG

What a great movement..

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • in general this shouldn't be any change. but in general questions like this it be nice to know the specifics of the watch in other words how was it performing before it was cased up and what is it doing now.
    • just as a reminder this watch is a Swatch group product. This will bring up a problem like spare parts and technical information. that I found some links to some information on when I talk about your watch and some of the technical and basically your watch is equivalent to 2834-2 for which I'm attaching the technical sheets. But equivalent does not mean exactly the same you want to do a search on the group for C07 as we discussed this watch before including the technical differences how it's supposed to be regulated and basically because it's watch group there is no parts availability. https://calibercorner.com/eta-caliber-c07-xxx/   https://www.chrono24.com/magazine/eta-movements-from-the-2824-2-to-the-powermatic-80-p_80840/ https://www.watchuseek.com/threads/h-10-movement-details.4636991/ eta CT_2834-2_FDE_481857_15.pdf
    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
×
×
  • Create New...