Jump to content

Can you align the minute and hour hand by pushing them into place?


Recommended Posts

Hey folks! Just made an account for a quick question. I've found a spec of something on my Seiko SKX011 dial and I've decided to remove the movement and dial from the case to clean it off. Another thing that's irritated me a bit since I recieved this watch is that hands aren't aligned properly. If the hour hand is at 12, the minute will be at 55-57. So I've decided to try and fix that while it's apart. If anyones wondering I do not have a handset removing tool. Thanks for any help in advance!

Link to comment
Share on other sites

there are many techniques and skills required just to remove the movement from the case.  Resetting the hands is not as straight forward as one might think especially if you have a day date chapter ring.

you will need to buy some tools and watch a few of Marks vids first 

  • Like 1
Link to comment
Share on other sites

If you had a pair of small/fine screwdrivers you could use the tips to carefully remove the hands. Afterwards you can align them as you please and push them inside. Ideally you should also need a pair of tweezers.

You don't necessarily need special tools for this, if you're careful. The hardest part is to remove them, installing is easier.

Tip: use transparent plastic bags as protection for the dial and hands when "operating".

Also, watch some youtube videos. Here's one from Mark the forum owner.

 

  • Like 1
Link to comment
Share on other sites

If you tried just pushing on the hands to get them to sync better chances are when you push the minute hand the hour hand will just move accordingly. You'd just in essence be setting the time, but doing so through the hands like you would on many old clocks as opposed to setting through the crown. Hands would need to come off and refitted. 

  • Like 1
Link to comment
Share on other sites

4 hours ago, burnsthewatchcollector said:

If anyones wondering I do not have a handset removing tool. Thanks for any help in advance!

You may not even need it. Pull crown to set time position and hold it while gently adjusting the minute hand. Or use two wood or soft plastic sticks to hold hour while touching the minute. For minimal adjustment that is acceptable but for anything else get the basic tools, they are very affordable.

  • Like 1
Link to comment
Share on other sites

1 hour ago, jdm said:

You may not even need it. Pull crown to set time position and hold it while gently adjusting the minute hand. Or use two wood or soft plastic sticks to hold hour while touching the minute. For minimal adjustment that is acceptable but for anything else get the basic tools, they are very affordable.

Definitely hold the crown and don't hold the hour hand if you're going to try to take this shortcut. Depending on how tight the hands are you are liable to damage the tiny and delicate pinion leaves on the minute wheel that drive the hour wheel.

  • Like 1
Link to comment
Share on other sites

1 hour ago, vinn3 said:

   NoNoNo; 

+1

All I can say is... you might not break anything.... but there is a reasonably good chance you will strip some teeth, bend something, break something... scratch something...  or in some other way, have a bad day. 

  • Like 1
Link to comment
Share on other sites

26 minutes ago, watchweasol said:

Hi I think the straight answer is to remove the sweep hand and Min hand align the hour hand and then re fit the min and sweep hands do not force/move the hands in situ as Andy says could end up wit problems

That is right by the book. But having worked on very, many watches identical to the OP's, I can tell that is not that easy to break the very robust 7S26 motion works. On the other hand (pun intended) I got a second hand tube snapped using a presto tool. I can't say if using levers would have made any difference. There is always a possibility that something breaks due to pre-existing fault, even when handling it the right way.

  • Like 1
Link to comment
Share on other sites

6 hours ago, AndyHull said:

+1

All I can say is... you might not break anything.... but there is a reasonably good chance you will strip some teeth, bend something, break something... scratch something...  or in some other way, have a bad day. 

   what about bending or breaking a dial hand?

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • in general this shouldn't be any change. but in general questions like this it be nice to know the specifics of the watch in other words how was it performing before it was cased up and what is it doing now.
    • just as a reminder this watch is a Swatch group product. This will bring up a problem like spare parts and technical information. that I found some links to some information on when I talk about your watch and some of the technical and basically your watch is equivalent to 2834-2 for which I'm attaching the technical sheets. But equivalent does not mean exactly the same you want to do a search on the group for C07 as we discussed this watch before including the technical differences how it's supposed to be regulated and basically because it's watch group there is no parts availability. https://calibercorner.com/eta-caliber-c07-xxx/   https://www.chrono24.com/magazine/eta-movements-from-the-2824-2-to-the-powermatic-80-p_80840/ https://www.watchuseek.com/threads/h-10-movement-details.4636991/ eta CT_2834-2_FDE_481857_15.pdf
    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
×
×
  • Create New...