Jump to content

Where to find a case back opener for Rolex


Cliff

Recommended Posts

I recently purchased set of Hedapai case back openers, but the none or the sizes fit a vintage Rolex Date. The closest one is a no. 5 (22.50mm), but it slips, so I don't want to use it. 

Does anyone know where I can puchase one that fits a Rolex Date? Also what size case back dprovket should I be looking for? 

Thanks.

Link to comment
Share on other sites

Are you using a bench opener? If not, that's the reason why it slips on a tight caseback.

With a bench opener you could use a soft plastic die. They come in a set of sizes and are not expensive. 

BTW, we have a section here where it's considered polite for new members to introduce themselves. 

Edited by jdm
Link to comment
Share on other sites

They only work on some non tight Rolexes. I purchased the Horotec case opener which accommodates dies for many calibers. Expensive but works every time. Previously I had purchased a Chinese Rolex opener set and the dam thing kept slipping, hence the Horotec purchase. 

  • Like 1
Link to comment
Share on other sites

The precision of the die is surely important but even before that comes using a bench opener not the handheld, and, of course, using the correct die. OP mentioned that No. 5 - 22.5mm  isn't correct, but actually No. 5 is 29.5mm, No. 2 and 22.5mm. So, what size is this caseback?

Check this for sizes not included in a 6 dies set.  https://www.aliexpress.com/item/32882400939.html

Link to comment
Share on other sites

4 hours ago, clockboy said:

They only work on some non tight Rolexes. I purchased the Horotec case opener which accommodates dies for many calibers. Expensive but works every time. Previously I had purchased a Chinese Rolex opener set and the dam thing kept slipping, hence the Horotec purchase. 

Looks like we both had the same problem with the budget Chinese die set. I'm going to look into the Horotec. Esslinger also has a L--G case back holder with dies for $99 designed for Rolex oyster cases. It fits right into an existing vise, so that may be the least expensive option for me.

Link to comment
Share on other sites

jdm - I made the mistake of purchasing a cheap Chinese case back die set, in relation to which, the no.5 (29.5mm) slips when opening the back of a Rolex Date. A "30.5mm" would likewise be even looser, ostensibly resulting in even more slippage. 

Link to comment
Share on other sites

4 hours ago, Cliff said:

jdm - I made the mistake of purchasing a cheap Chinese case back die set, in relation to which, the no.5 (29.5mm) slips when opening the back of a Rolex Date.

I understand that. But you have not clarified if that is using a bench opener or the handle. The first is always necessary with tight case backs of any design.

Link to comment
Share on other sites

I've opened difficult case backs with both methods and it makes no difference as long as the case is firmly secured in a holder.  I place my holder in a jeweler's vice and it works great. The problem arises when a dye is not manufactured to tight specs, you are going to get slippage, which is exactly what happened here.

I didn't have a die for this specific Rolex model, so i hastily made the mistake of purchasing this crappy Hedapai Chinese set of case back openers. Learned my lesson the hard way.

 

 

Link to comment
Share on other sites

8 minutes ago, Cliff said:

I've opened difficult case backs with both methods and it makes no difference as long as the case is firmly secured in a holder.  

From my direct experience I don't agree. 

A bench opener is a must when dealing with a tight caseback. It allows placing axial force precisely.

Link to comment
Share on other sites

jdm - when I worked for a jeweler one summer, we used different approaches. I had a few case backs where the old gaskets acted like a glue and were stuck, similar to when a rusted bolt is seized. I ended up using a wing bar case back opener and attached two steel sleeves that fit over each wing, thus providing more torque in order to open it.  Improvising and overcoming is more important than adhering to one method.

 

 

Link to comment
Share on other sites

I stand my case. You can only apply torque after axial force has made the tool securely grab into piece. My bench opener is among my unreplaceable tools and best money spent, it's China made BTW. This is my last post in this topic, good luck. 

Link to comment
Share on other sites

You can pretty much open any case utilizing downward arm pressure with an opener and die that is correctly sized. Because your particular method and Chinese tool works for you, doesn't equate with the only method. In any event, I purchased the L-G case back opener and dies, which will arrive this week. I will post my comments about it.

In my view, tools manufactured in China, be it for watch repair, home improvement or auto repair are sub-standard, as is the steel and tempering process they utilize in making those tools. Because steel is the very foundation and ingredient of a well made tool, any compromise in that area will result in sub-standard tools. 

Needless to say, sub-standard case back openers like the Hedapai always end up costing more in the long run.

 

 

Link to comment
Share on other sites

I bought one with a single die, ebay so chinese that stated for Rolex. Going on that one diameter isn't what matters only the fit of the "knurling". I only use it to change the battery on an oysterquartz and my recollection is that it's a little smaller in diameter than the case back. It's ok to use providing that enough downforce is applied but it fits well.

John

-

  • Thanks 1
Link to comment
Share on other sites

I received the L-G case back opener and dies today, and it totally rocks. Good steel and quality throughout. Perfect alignment with cases and fits nicely into any workshop vice. Best $99 I spent!

Unfortunately, I didn't have a 29.5mm die which is the reason why I bought the Hedapai set. In the long run, I ended up spending more by working with a sub-standard tool; hence, a valuable lesson learned.

DSC00434.JPG

DSC00437.JPG

DSC00436.JPG

Link to comment
Share on other sites

On 1/5/2020 at 1:48 AM, clockboy said:

Unfortunately with Rolex backs force is not the answer. You must have the correct die or it will slip. I speak from experience. 

Agreed, the Hedapai 29.5mm is larger than the L-G 29.5mm die I just purchased. In short, it is out of spec to a Rolex case, which is why it slipped.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • 🤔 leaving the EU meant that UK was no longer part of the convention and have already been turned down an independent reapplication. I'm pretty sure courts have to be held in Switzerland in this case. There will be a lot more watches stashed away in draws  tbh, folk wont be able to afford to maintain them. Cheap watches will be bought and top end watches by folk with plenty of cash that can pay for service and repair. The expensive once in a lifetime gifts and everything else inbetween will be at the forgotton when they stop working. I know i was being a numpty, get used to it 😄 Anybody that knows will boycott them, but besides repairers who will know. Nope will never buy one, i made that decision as soon as i learnt about this. 
    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
×
×
  • Create New...