Jump to content

Sicura D500 Jump Hour


rustycolt

Recommended Posts

I have been looking for one of these for quite a while, and finally found the right one. Bought from the bay as a project, it was a bit hard done by when I received it, but that it what I was after. Right off the bat, it needed a new balance staff and full service. I ordered a complete balance, as the existing hairspring was not inspiring confidence, and I have yet to develop any hairspring repair skills. Turns out that the BFG866 movement has two different hairspring configurations, which in turn use two different regulator/stud mount posts. They physically work together when they are wrong, but the hairspring becomes distorted due to incorrect y-axis positioning. I have located the parts to correct this, it shall be done. In addition, I have found that the power reserve is a meagre 11 hours or so, as such, I've placed an order for a new mainspring. Today is the second day that I have worn it, and I can see that I will need to go back in and tighten up the canon pinion a little also. So still a couple more tasks on the worksheet for this watch, and I wouldn't normally wear a work in progress, but now that the replacement glass is installed, I couldn't resist putting it on this morning. 

 

Many thanks to fellow WRT member noirrac1j who has been a tremendous resource throughout this project, and who was the key to sourcing a replacement crystal - that was a huge deal, my gratitude to him for the help, and to Mark for creating this community for us to find each other in!

 

Here is the poor thing before - I was able to polish out about 95% of the scratches and pits from the crystal, but that only revealed that there were two significant cracks, and a crater at 8:00. 

post-456-0-60340900-1420727206_thumb.jpe

 

I was able to do some light polishing on the case, but the plating is pretty thin, and I'd rather live with a few honest scratches than brass edges, so for now, this will suffice. There is a decent chance that the bracelet is original, but I do not know for certain. The clasp has been repaired at some point, and it was done well. I think the cost of that repair would have exceeded a replacement bracelet. It is not signed, but for my purposes, I'm willing to accept it as an original part (for the time being, at least)

 

post-456-0-04636700-1420727906_thumb.jpg

post-456-0-90151000-1420728078_thumb.jpg

post-456-0-84782500-1420728103_thumb.jpg

post-456-0-83980400-1420728133_thumb.jpg

post-456-0-01321600-1420728177_thumb.jpg

 

All in all, it's good fun, and that is exactly what I bought it for. It's roughly the same vintage as I, and while that was not an era known for its timeless style and beauty, it is satisfying to embrace that bit of nostalgia and individuality. 

-J

 

  • Like 1
Link to comment
Share on other sites

Good job and fantastic photos Jeremy! Maybe a shot of the movement when you work on the cannon pinion or change out the balance? By the way, I actually have an original signed sicura bracelet for this watch. The bracelet I have is good quality, flexible, etc. and has also been repaired at one of the links. I don't have it on my watch because I happen to like leather straps. I have both original and refinished examples of the watchcase, and I prefer the "sunburst" brush finish which is difficult to reproduce because it is radial--at least that is what they told me.  I love the uniqueness of the Sicura's and it always gets noticed when I wear it.

 

JC

Link to comment
Share on other sites

  • 4 years later...

Sorry to dig up an old thread, but I had to say what a wonderful job you made of this. If you are still around (4 years is a long time, ha ha) do you have details of where the crystal came from as I have just bought one of these myself and joined the forum because of this thread.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
×
×
  • Create New...