Jump to content

esslinger kit watch help


paul1100gpz

Recommended Posts

Hands should be pressed on lightly. Make sure they do not rub each other and don’t touch the dial. When it comes to casing up the movement make sure the hands are clear of the glass. You do not say if it is a center seconds hand or sub seconds. Sub seconds make sure it is clear of the dial and is not rubbing anywhere on the dial. Have you tried the watch without the second’s hand? If the movement works, you know where to look.   

Link to comment
Share on other sites

I believe it is a NH 36 movement. it is a  center second hand.. Yes, it does seem to run without the hands.  I have purchased another movement on Ebay. Just haven't gone back to work with it.  It was no problem putting on the Hour and minute hand. The second hand was a problem. I fear I may have pressed to hard. Getting them off was and is quite a chore. The kit in question was there retro kit when I purchased it, it was $140 now $200.

4 hours ago, jdm said:

And which watch is that? Does it run good without hands? yes it did , I will have to get you the product # .at this point I will have to try and remove the hands and see how it runs.

 

 

Link to comment
Share on other sites

1 hour ago, paul1100gpz said:

The second hand was a problem.

Gently place the second hand on the pinion. Once it is right it will start turning. Do no press until that happens, if does not then lift it and try again. Then press vertically with the tip of tweezers, or tapered pegwood.


The quickest way to upload smartphone pictures is to write the posting directly on the smartphone. If the posting requires too much writing to be done comfortably on the smartphone, do that separately on the desktop.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hi. Breaks like this can br fixed with conductive paint like the paint used to repair a car  rear screen heater. I have used it successfully, you don’t need much and unlike solder there is no heat 6020A-1.pdf
    • the problem with vintage watches and yes quartz watches can be vintage is availability of parts will be a problem. I have a link below where we can cross reference the coil and  I was hoping for more. Another problem for vintage parts are everyone on the group gets used to ordering from online. Conceivably the physical material houses that still exist out there might have the part and you'd have to reach out to them and see if anyone has one. this is because they don't list every single part that they have online with the exception of cousins where everything they do is online work just doesn't exist but the other material houses can have stuff not listed. Otherwise just set up a search on eBay and sooner or later it will possibly show up if you're lucky.   http://cgi.julesborel.com/cgi-bin/matcgi2?ref=SEK_6020A  
    • Hi welcome to the forum.    Enjoy
    • the bestfit book refers to Revue as wittnauer and the fingerprint we have this.
    • Maybe a little off-topic, but it still amazes me that most people (and myself before I got into this hobby) don't realise that the movement of their watch was (in most cases) not made by the name on the dial of the watch. This is especially true of many 'fashion' watches which use the cheapest of cheap movements ($4 each) which are completely out of proportion to the overall cost of the watch ($++100s). Usually the actual manufacturer is stamped somewhere inconspicuous on the movement, usually around the balance, and this is what you need to find so you can locate spare parts or servicing manuals etc. This is like buying a top of the line Rolls Royce Phantom and learning it has a BMW engine..... oh wait a minute, it does! (6.75-liter, 460-horsepower BMW V12 engine - reference)
×
×
  • Create New...