Jump to content

What Movement??

Paul78
 Share

Recommended Posts

rogart63 Distinguished Member

rogart63

Posted
Posted

Found it while searching for a picture of the other side of the movement . Have one i don't seam to get together . Having trouble with the upper bridge . Need to have four or five small pivot i the jewels before i can put any pressure on the bridge . If i leave the second wheel out it works . So my thinking is there is something wrong with that wheel . The movement had a really slow amplitud but it's really clean inside . Becuse i can't fix i am so mad i don't want to see the movement for a while at least . Put it away somewhere dark . Maybe i can find a nice cheap  AS 1882 movement somewhere instead . If so i could have some nice parts for a AS 1882 . 

Link to comment
Share on other sites
  • 3 years later...
Siro Member

Siro

Posted
Posted
On 5 January 2015 at 9:47 PM, Paul78 said:

I have a Rotary 21 Jewel Automatic, it has a broken setting lever spring. The movement has absolutely nothing on it to distinguish it other than stamped on the rotor ' 21 Jewel Swiss Made '

If there is nothing on the movement how do I know what to look for?

This would obvsiously help me with other brands not just rotary so my question I suppose is, how do I know what I'm looking for??

There is something on the barrel bridge that may be significant but I can't make it out from your pic. 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      My first Gruens. Precision 510 and N510R movements.

      By rjenkinsgb · Posted

      Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one).   Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots.  
    • rjenkinsgb
      Any tips to correct a sloppy error?

      By rjenkinsgb · Posted

      Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
×
×
  • Create New...