Jump to content

Dial (face) cleaning?

64americandeluxe
 Share

Recommended Posts

Kraai Watch Enthusiast

Kraai

Posted
Posted (edited)

A dial from a Bulle clock (model XC) looks dirty. Varnish remover does not help. Sanding and  resilvering is not possible because the letters are not engraved.

Please help, thanks, Kraai

 

Dial Bulle clock XC.JPG

Edited by Kraai
Link to comment
Share on other sites
  • Replies 371
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

64americandeluxe
64americandeluxe

My dad's 30-ish year old Seiko has white crud at the 12:00 marker.  I think it is adhesive from an old repair (possibly a crystal repair with the dial still in the case?).  Any thoughts?  Would it be

Bill3
Bill3

Thank everyone who responded to my question about cleaning a watch dial. better What a treasure trove of useful information! I was doubly surprised to get so much good information, especially since t

Graziano
Graziano

Hi there LittleWatchShop ,on that particular dial I would go no further than saliva (enzyme solution ) on a q tip .It will not remove printing and lacquer only dirt and leave it at that. But don't do

Posted Images

Chopin Super WRT Addict

Chopin

Posted
Posted

Without messing it up you will only be able to clean it up by about 25% or so... Even that can be a tad risky, especially with the indexes, writing, numerals, etc.

It looks good as it is if you ask me. It has personality and patina. Not gonna be able to make it look brand new.

I would say that your only bet is to lightly tap the dial with some cleaning substance and some cotton and that's about it. If it'll remove some of the dirt then that'd be good enough.

Link to comment
Share on other sites
mikecj Member

mikecj

Posted
Posted

Y'all,

Just purchased a 90 year old watch. It still runs. The only issue the dial face has some patina (read dirt), oxidation and minor paint loss. Can you provide me recommendations for:

1. Removing the dirt.

2. Dealing with the oxidation.

3. Replacing the lost paint.

The dial face appears to be paint on metal.

Thank you,

MikeCJ

Link to comment
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
carlos123 Watch Enthusiast

carlos123

Posted
Posted

Hi all,

 

I’ve recently got my hands on a Seiko divers watch which needs a little work. When I first got the watch I noticed what I thought was a fingerprint in the underside of the glass, however on removing the movement I noticed the mark was actually a shiny part of the dial rather than the matt finish.0dcebd3bf356e16fb8c90f3e51e85c9b.jpg

 

I’ve tried cleaning/lifting with Rodico and some solvent cleaner without any joy.

 

Does anyone know if there is any way to restore the Matt finish? I don’t really want to buy another dial as I prefer it to be original to the watch.

 

Thanks in advance

 

Carl

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
AlexeiJ1 WRT Addict

AlexeiJ1

Posted
Posted

You know if you wanted to experiment? You could try some degreaser or light soap and then gently touch it with your finger, then rinse/dry.

Yes there is a risk the dial will be destroyed, but there is a chance it will remove the oil stain if that is indeed what it is.

I did ruin a dial that had battery acid damage by washing it - but it was still usable its just that the awesome patina from the acid was washed away with water.

Link to comment
Share on other sites
luiazazrambo Super WRT Addict

luiazazrambo

Posted
Posted

You could try to take a picture of it and edit (removing the dirt and to make it 1 to 1) it in GIMP for example then you could use the same technique what Mark used in his video: 

 I am not sure how difficult it would be to find a spare dial to use that for the experiment and not the original one. I also like the original as it is.

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
8 minutes ago, luiazazrambo said:

You could try to take a picture of it and edit (removing the dirt and to make it 1 to 1) it in GIMP for example then you could use the same technique what Mark used in his video: 

GIMP is an image transformation tool with very poor technical drawing features. One needs Illustrator, or Inkscape to work on dial blueprints.

  • Like 1
Link to comment
Share on other sites
wls1971 Distinguished Member

wls1971

Posted
Posted

I've used Gimp quite a lot for flat dials, just scan the original and edit out the defects, the beauty of this you can lay the new dial over the top of the old, so if in the future you decide you want a dial restorer to work on it you have preserved it for future restoration.

You can print on off white paper or card to make the dial look aged.IMG_20190613_0002.thumb.jpg.5c53cdbaba9a4b407a94892b6dde0966.jpg1300016454_clockdial.thumb.jpg.11226ab0a0458e9e042a24b15be8e406.jpg

  • Like 2
Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi  K  If its not a full on restoration I should give it a wipe over with mild soap and water then leave as is It got like that through the life it lead and is therefore the character of the clock.  I personally like to leave things alone as long as its not detremental to the operation of the clock, we all pick up a few cuts and bruises through life.

Link to comment
Share on other sites
Lenj WRT Addict

Lenj

Posted
Posted

Also got me thinking, you may recall I wanted to get an Epee dial restored, but to expensive, I love what Mark did in his video, I was wondering if I could do the same, does it have to be printed with laser printer? or would normal printing be OK on the special paper??

 

Thanks Len

epee1aa.jpg

Link to comment
Share on other sites
wls1971 Distinguished Member

wls1971

Posted
Posted

I've used all sorts of paper a high gloss photo paper printed on a inkjet does a good job of looking like an enamel dial. I use a canon inkjet there is a setting on it that puts more ink onto the paper for the blacks, Epson heavy weight matte paper is fantastic for  non glossy printed dials it has a very fine surface finish to the paper.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Without Our Forum

      By RichardHarris123 · Posted

      In the meantime whilst awaiting a better plan, please drop me a quick hello on my email. 
    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      I looked at it like this, I've built a lot of stuff in my time, building structures and furniture,those are my creations and they will still be here way way after I'm gone. Traditional watchmakers felt the need to pass their knowledge on, ideas that they created . I assume with them as it is with me, leaving their mark on the earth, a way of being remembered. This creation of Mark's has brought thousands of people together to pass their knowledge around,  ideas that will continue to be used for lifetimes. Ideas that should continue to be procured. If for whatever reason the forum ceased to exist, not quite like Ranfft's, that didn't disappear but much less usable. Then that is sad, such a massive loss of communication between good people and a wealth of knowledge lost. There should be something in place for when that happens which could be next week, next year or in 10 years. Might not be a topical subject for a lot of folk or boardering on controversy, i did say i talk about stuff other people dont. But if you dont talk about it and something happens then you've lost it and you ain't gonna fix it .
    • Waggy
      Without Our Forum

      By Waggy · Posted

      I've remained silent on this thread, and at the risk of upsetting everyone, the thing that worries me the most the the apparent absence of Mark. The moderators do a great job and the members also pitch in, and the site seems to run itself, but it is a concern for the future of this forum when the owner is absent for all intents and purposes. Like many of the comments above I would hate to log in one day and things be closed down as I rely on this site for ideas and knowledge and also cheer me up. maybe the Moderators could reach out to him, assuming he does not read this thread, and express our concerns and let us know the plans going forward? some kind of WRT ark
    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      That was the exact reason for me starting this thread watchie. Still we haven't worked out how the regulars are going to hook up if it goes tits up. I honestly think something should be arranged to stay in contact, we all help each other so much. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Yeah ive watched that a few times before,  i couldnt find my old school dividers to scribe it up 😅 Yep thats the guy i bought a roll from . Thanks Nicklesilver that answers that perfectly and more or less what i thought an experiment over time would prove . The jumper arm is quite thick along its length, i left it that way intentionally, i thought the original was probably very thin, i didnt see that it was already missing. Setting isn't particularly stiff as such just positive, i still need to take it out and polish where it mates with the stem release. 
×
×
  • Create New...