Jump to content

Teaching Class

jdrichard

By jdrichard
in Watch Repairs Help & Advice

 Share

Recommended Posts

nickelsilver Distinguished Member

nickelsilver

Posted
Posted

As a former teacher I will weigh in:
You have to present the material to be instructed, here a balance staff, and this will be broken down into the steps necessary, and the reason given for each step.

We assume a basic level of lathe turning knowledge here.

Are you doing all in collets? Some in collets some between centers? All between centers?

Are you going for a "tic tac" staff that runs, or a staff that gives original performance?

Are you going for original performance and original appearance, such that the next watchmaker doesn't notice it's a non original staff?

For the different expected outcomes different steps would be involved of course. Also different levels of precision accepted; an 18s American pocket will differ greatly from a JLC 104.

What's your current lesson plan?

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

My master taught me by demonstration, sitting down next to him; he would explain what he was going to do. From teaching me how to sharpen the gravers, how to cut, what types of gravers to use and why, types of metal. For me that is how I learned. You learn by your mistakes and I had plenty of those. The type of lathe is very important. You have to know the lathe; I had a foot control which helped a lot. I started by cutting a very large balance staff, working down to a Pocket Watch size and finely to a small cal Ladies watch. It was a Lathe made by Boley. Don’t forget back in the early 70’s we didn’t have computers to help you out with the measurements you had to know the math. Pocket calculators were only just coming on the market. I do sound out of date.:D

I wish you luck. I know teaching a class is different to what I have added. This might help in some way. I used to teach IT many years ago to uninterested didn’t want to work students, at least you will be in front people willing to learn and will find the subject interesting.

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted

NickleSilver and OH, thanks for the feedback. I am planning on a lesson plan as follows:
- What is a balance staff
- Removing and keeping the old staff
- Tools needed to cut a staff
- Gravers and Sharpening
- Basics in cutting
- Measurements and old staff
- Friction fit or Rivet
- Blued Steel and (perhaps tempering)
- Selecting and prepping the blued steel
- Phase 1 - Cutting the Balance Surface
- Phase 2- Cutting up to the rivet or balance edge (friction fit) and fitting the balance.
- Phase 3 - Cutting the HS Collet surface and fitting the HS
- Phase 4 - Cutting the upper Pivot and finishing the upper pivot.
- Phase 5 - Cutting the rolled table surface (rough cut)
- Phase 6 - Cutting off the staff and flipping around in Lathe
- Phase 7 - Finishing the RT side and fitting the RT to its friction stop point
- Phase 8 - Finishing the Lower Pivot
- Phase 9 - Staking in the Balance and Riveting(as needed)
- Phase 10 - Staking on the RT
- Phase 11 - Jacot Tool and Pivot polishing and sizing the balance staff.
- Phase 12 - pressing on the HS

I do plan to spend some time on polishing the pivots while the staff is still on the lathe. As well, I plan on showing how you use the old balance staff to measure the cuts. I will also show the use of the Jewelled Gauge to measure the pivots and you bring down the size and how to leave a little extra for sizing with the Jacot. I also have a set of vintage pin gauges that I will use to measure the pivot size on the movement lower and upper jewels.

Thoughts??


Sent from my iPhone using Tapatalk Pro

  • Like 1
Link to comment
Share on other sites
measuretwice WRT Addict

measuretwice

Posted
Posted (edited)

3 hour workshop.....does that mean they'll all have lathes and be trying things?  You could hold a class for half a football team and give them each their own lathe to use lol.  Three hours is a lot of air time to fill without including a pile of audience activities.  I would say the approach and content would be dependent on who the audience is, and what the venue/media/forum.  Whats their knowledge level on a) watches and b) machining?

I've not taught a class but I've written many articles and I see a similarity in that I think either make you better at it.  You might know 95% of a topic which is perfect for heading into the shop and making something, but all of sudden when giving instruction you feel a lot of pressure to figure out and know cold that last  5%!

 

Edited by measuretwice
Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

I'm guessing this will be for a NAWCC meet? Will you be demonstrating the whole procedure? Will this be hands-on with folks bringing lathes? 3 hours for an overview, explanation and slideshow (yeah I know, it's Powerpoint but the last time I gave a talk it was with the help of Kodak), with perhaps some demonstration sounds a little long. But if there are several lathes available and the group isn't too big, then most/everyone can try their hand at this or that aspect while asking questions and there goes an hour or two right there. But if it's just a presentation I would say about an hour/hour and a half is enough. An hour and a half is already stretching the attention span of most folks for a lecture no matter how interested they are.

 

Your lesson plans looks good, of course many of the points (like Jacot use) could be a class on their own, but you seem to have everything covered.

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
3 hour workshop.....does that mean they'll all have lathes and be trying things?  You could hold a class for half a football team and give them each their own lathe to use lol.  Three hours is a lot of air time to fill without including a pile of audience activities.  I would say the approach and content would be dependent on who the audience is, and what the venue/media/forum.  Whats their knowledge level on a) watches and B) machining?
I've not taught a class but I've written many articles and I see a similarity in that I think either make you better at it.  You might know 95% of a topic which is perfect for heading into the shop and making something, but all of sudden when giving instruction you feel a lot of pressure to figure out and know cold that last  5%!
 

Most likely 4 or 5 people. Will determine the level of experience prior to the session. Also not sure at the moment whether the students will be bringing lathes or if I will bring a few of my lathes, I do have 6 on Borel stands all ready to go. On your 5%, I am not being paid so no need to get stressed out.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I'm guessing this will be for a NAWCC meet? Will you be demonstrating the whole procedure? Will this be hands-on with folks bringing lathes? 3 hours for an overview, explanation and slideshow (yeah I know, it's Powerpoint but the last time I gave a talk it was with the help of Kodak), with perhaps some demonstration sounds a little long. But if there are several lathes available and the group isn't too big, then most/everyone can try their hand at this or that aspect while asking questions and there goes an hour or two right there. But if it's just a presentation I would say about an hour/hour and a half is enough. An hour and a half is already stretching the attention span of most folks for a lecture no matter how interested they are.
 
Your lesson plans looks good, of course many of the points (like Jacot use) could be a class on their own, but you seem to have everything covered.

Thanks for your feedback. I am hoping to get some hands on from these folks as the only way to help is to see what they might do from a skill level. I suspect that non of the 5 expected to attend have ever cut a balance staff and really want to see if this is something they want to dive into. I’ll fill you folks in after I get a bit more detail on the attendees. My first time teaching this, but I did teach the internet years ago and also taught armoured corps tank troop tactics in my youth.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
  • 2 weeks later...
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted

Workshop went well. Cut 90% of a staff, showing all elements of measuring and cutting for balance, Hairspring. Did not finish roller table side but all were good with the information passed along and videotaped. Asked to do another in Jan.


Sent from my iPhone using Tapatalk Pro

  • Like 3
Link to comment
Share on other sites
vinn3 Distinguished Member

vinn3

Posted
Posted

good show,  keep up the good work !   during my aprentisship,   there were a couple "old foot pedle lathes",  about 4 inch.  as i rember,  his main point points were "sharpening cutting tools and you don't always need high speed to make a good cut".   hang in there,  vin

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
good show,  keep up the good work !   during my aprentisship,   there were a couple "old foot pedle lathes",  about 4 inch.  as i rember,  his main point points were "sharpening cutting tools and you don't always need high speed to make a good cut".   hang in there,  vin

Thanks Vin, all good. A little tricky cutting with folks breathing down your neck:)

Sent from my GT-N5110 using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...