Jump to content

Pallet Warmer Project


Mark

Recommended Posts

Editing a video on the construction at the moment. 

Need to reset the pallet stones in a vostok which was loaded up with too much shellac. Unfortunately my pallet warmer is missing - searched high and low - I suspect it's in pallet warmer heaven. So I made a new one. Hopefully this will be an interesting video for some. In fact - I made two. Will do a giveaway to a winner for one of them. Details will be announced in my next video which will show how I made these and the video after that will the Vostok restoration where I will demonstrate how they are used.

In the meantime - if anybody wants to build one themselves, I have attached the plans to this post. If you do make one then post pics :)

pallets.jpg

pallet-warmer.jpg

pallet-warmer2.jpg

pallet_warmer_sketch.png

pallet_warmer_sketch2.png

Pallet Warmer Plans.pdf

  • Like 3
Link to comment
Share on other sites

Nice one, thanks for the plans.... Strangely enough I was just looking for mine before reading this and found it.
Maybe your lost one is with Bagpuss?
1996946093_20191111_1252421.thumb.jpg.ca93f72c392349a88ce9b5395c8aa033.jpg
Yikes - bagpuss. Now that's a blast from the past!

Sent from my SM-G950F using Tapatalk

  • Like 1
  • Haha 2
Link to comment
Share on other sites

32 minutes ago, watchweasol said:

Hi  Likewise Old H do you remenber Andy Pandy and Teddy , Watch with Mother,   not forgetting the Interlude....

Watch with Mother Monday

Andy Pandy Tuesdays

Rag Tag and Bobtail Wednesday

Bill and Benn Thursday

The Wooden Tops Friday.  

Link to comment
Share on other sites

A nice video Mark. What type of lathe are you using?
@oldhippy Sorry for late reply.
It's a mini bench lathe made by a company called Optimum. A relatively new addition to the workshop along with the mill.
761cd7f46b1fd130a335b5ee54b960dc.jpgefd09d341be590b70a66549f5ac6e60a.jpg

Sent from my SM-G950F using Tapatalk

Link to comment
Share on other sites

1 hour ago, TheFixer said:

I have the copper plate so just need some brass.

Any chance of a picture with the wooden holder without the tool itself?

You can see it clearly in the video Mark uploaded, he shows the machining out process but it could be easily done with a chisel or by tacking sides onto a flat piece.

  • Like 1
Link to comment
Share on other sites

On 11/15/2019 at 10:59 PM, oldhippy said:

Thank's Mark for the reply and nice photo. That's a new one on me I'll look that one up. 

Is it the Light Duty Lathe Optimum TU2004V 240v Variable Speed?

Absolutely - thats the one. So far I have had a few issues with it but noting major.

The gib in the compound slide was bent - easy fix but I need maybe add a couple more gib screws to make it more smooth and it came with an extraordinary amount of grit on the lead screws and ways. This is common with chinese lathes I think but didn't expect it with "German quality" - lesson learned :D

I would like to install a thrust bearing too, to minimise  backlash. But the parts I have made so far are quite accurate not bad for a light duty lathe. Not unhappy.

 

13 hours ago, TheFixer said:
I have the copper plate so just need some brass.
Any chance of a picture with the wooden holder without the tool itself?

There you go9fd5114a1d5f9cd0f0957a0133eaa82d.jpg

Sent from my SM-G950F using Tapatalk
 

Link to comment
Share on other sites

8 hours ago, Mark said:

Absolutely - thats the one. So far I have had a few issues with it but noting major.

The gib in the compound slide was bent - easy fix but I need maybe add a couple more gib screws to make it more smooth and it came with an extraordinary amount of grit on the lead screws and ways. This is common with chinese lathes I think but didn't expect it with "German quality" - lesson learned :D

I would like to install a thrust bearing too, to minimise  backlash. But the parts I have made so far are quite accurate not bad for a light duty lathe. Not unhappy.

 

There you go9fd5114a1d5f9cd0f0957a0133eaa82d.jpg

Sent from my SM-G950F using Tapatalk
 

Thank you Mark that is very helpful.

Link to comment
Share on other sites

  • 4 weeks later...


  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello again, I meant to say the movement above was in a Chronosport Atlantis 20 ATM on eBay and wondered if you had the same movement in your watch, all the other Chronosport watches had auto-matic movements....
    • Also been looking at the same ones as Tom 0.1.- 1mm around 55 quid inc shipping. The pivot straightner i have runs from 0.07  -  0.15 in increments of 25 microns.  I guess you could use a balance staff of sizes under 0.1 to make up the remainder of the lower sizes.
    • I have always had it in my mind that hairsprings can fatigue in just the same way as mainsprings can. If a hairspring has gone through a rough process of repair then its structure will have changed ( bending any metal backwards and forwards will cause micro fractures and eventually breakage ) in those areas of heavy manipulation. Its strength and elasticity is no longer linear over its full length so no longer isochronical.  
    • This seems to be complicated case... We have many variables here and we need to exclude some of them to make some progress. We have plots that show amplitude variations, but we don't know if this variations are significant, as they can be 'amplified' or 'smoothed' by the software. So, some observation of the amplitude by eye will be of help. Then, if we really have not isochronical work, then the main reason for this would be the hairspring being not 'linear'. And not linear may be sometimes not only because 'touching', but because bad hairsping material structure. Some of the advanced watchmakers claim that repairing badly bent hairspring is useless, because this springs will never be isochronic again.  Well, my own observations are that such thing happens, but not in all the cases and it depends on the case if the result is acceptable or not. I will not suppose here that this spring has been repaired, but it has some strange behavior watching at it's work. It will be good if it is possible to test the movement with another balance or thest the balance on another movement...
    • The more common Jewel hole diameters are from about 0.07mm to 0.50mm. Those are the sizes in the Seitz jewel gauge tool.
×
×
  • Create New...