Jump to content

As Movement

Lolbear

By Lolbear
in Watch Repairs Help & Advice

 Share

Recommended Posts

Lolbear New Member

Lolbear

Posted
Posted

Hi Mark

Just watched your excellent how to video on the AS movement, I had to repair the winding mechanism following a drop. When replacing the parts I have lost the calendar jumper spring! Would / could you please advise me as to where I can get a spring for the calender jumper.

Cheers

Lolbear

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted

AS1691 has quite a lot of parts available. You can order from Cousins or PM GleaveandcoLuke (a member here, http://www.gleaveandco.com/) and he will help you.

 

If the crown wheel screw is broken then you can replace the barrel bridge - these are cheap, about £10, you can get an assorted pack of left thread screws no problem, and the calendar jumper springs are about a few quid but you may need to buy a pack of five.

Link to comment
Share on other sites
Blacklab Distinguished Member

Blacklab

Posted
Posted

I've spent many a happy hour on my hands and knees searching for a missing screw/ click spring or other small part.

 

RogerC

I have a nice big magnet for that, or try a long magnetic knife rack. Just demagnetise the part after you find it.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Oh nice. I have a similar wedge style stump for my staking tool, so I'll give that a shot. Thanks!
    • joelcarvajal
      Gamblin Gamsol for cleaning?

      By joelcarvajal · Posted

      Thank you all for the replies!  Very informative! True enough, the Gamsol took some time to evaporate and does leave a residue. So not all naphtha are created equal!  Need to find alternatives then. i was able to try Hexane recommended by Alex and it seems great.  I wonder what the cons are?
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀   Another thing I will need to consider is once the dial and hands are fitted and the movement is sitting in the case I will need to turn it over to put the case screws in. I saw a vid on Wristwatch revival where he lightly fitted the crystal and bezel so he could turn it over, is this the only option or is there another method?      
    • nevenbekriev
      Main spring

      By nevenbekriev · Posted

      Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
×
×
  • Create New...