Jump to content

O-ring lubrication


DPhillip

Recommended Posts

Hello, 

I was replacing batteries in two watches - a Pulsar over 20 years old and a year-old Timex, and I used an Esslinger silicon lubrication/grease kit to lube the o-rings in the watch backs.  The kit consists of sponges in a plastic jar, soaked in the silicon grease.  

Both o-rings expanded, making it impossible to re-seat the watch backs. The Pulsar back screws down, the Timex is a press fit.  I actually tested the fit on the Timex before installing a new battery and lubing the o-ring, as I had trouble with the Pulsar o-ring earlier and I wanted to record what happened.  As soon as I lubed the Timex o-ring, it got bigger - putting any pressure on the watch back causes the ring to ooze out one side or the other.

Any thoughts on what is going on here?  Esslinger has a good rep, I thought; I never figured their silicon grease product would cause something like this.

Is there anything I can do to shrink the Timex o-ring?  The Pulsar o-ring needs to be replaced - it is old anyhow.

Thanks!

Link to comment
Share on other sites

  O  rings expand:  esslinger screwed up.   probably bought chineeze rings with out specified the "rubber formula".   o rings made in the US and UK have a "specifide grease"  for each ring.   this happens with hydrolic seals also.   TO BE SAFE,  use Vasoline.  vin

Link to comment
Share on other sites

Hi Vinn is right the grease should not make any difference to the the ring other than coat it,  The grease may have a carrier liquid which is reacting with the sealing rings (being absorbed)  Try  dropping the rings into boiling water it may help shrink it, it used to work on dictating machine drive bands. If it works do what Vinn suggests and use vaseline. I use a tube of DOW CORNING silicone grease I used at work as a heat transfer for large transistors a s a thermal comductor  it works ok.

Link to comment
Share on other sites

1 hour ago, watchweasol said:

Hi Vinn is right the grease should not make any difference to the the ring other than coat it,  The grease may have a carrier liquid which is reacting with the sealing rings (being absorbed)  Try  dropping the rings into boiling water it may help shrink it, it used to work on dictating machine drive bands. If it works do what Vinn suggests and use vaseline. I use a tube of DOW CORNING silicone grease I used at work as a heat transfer for large transistors a s a thermal comductor  it works ok.

     it does make a difference.  vin

Link to comment
Share on other sites

On 11/6/2019 at 11:45 PM, DPhillip said:

Both o-rings expanded, making it impossible to re-seat the watch backs. 

I don't know of what these o-rings are made of, but as others have said the NBR normally used never expands and the grease actually helps keeping it in place. I suggest that you replace these and switch to a different grease. 

Link to comment
Share on other sites

I tried boiling the o ring and then using a heat gun on it.  Neither worked.  As soon as I pressed the back into place the ring oozed out of the groove a quarter of an inch.  The watch is only a small lady's Timex.  Bizarre.  I have to get a new o-ring, clearly.

Also, I test-fit the back and o-ring on the watch before using this silicon grease and it clicked into place just fine with no problem.  

So if we want to expand o-rings, perhaps to take out some enemy's missile program, this stuff is the ticket! 

BTW I emailed Esslinger about it - no reply.  

To be clear, the grease is an Esslinger product - the watch was made in India - not sure where they source their o-rings.

DP

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I think if you want to play Billy big b.ollocks then you have to have something up your sleeve, anyone that knows how to fight, plays dirty. Lets face it a lot of folk that voted for Brexit just rolled uk their sleeves to say up yours EU hoping for good changes. We have idiots for leaders and probably none of them clever enough to clean the shitty stick they were given. I didnt vote, what will be will be.
    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
×
×
  • Create New...