Jump to content

Seiko Mainspring Database?


jaycey

Recommended Posts

I was wandering...

 

As many Seiko complete barrel/mainsprings are beginning to command a kings ransom, has anyone seen or thought about an online resource for calibre/mainspring sizes when replacing just the mainsprings?

With a little care, just the mainsprings are replaceable & it would be a lot easier to look-up the spring size rather than measuring it.

 

I'm about to service a 4R36 so will be measuring that...

 

Link to comment
Share on other sites

First question, how do you know that the MS is to be replaced? It is not a mandatory item at each service interval.

Now, this isn't the first topic opene on the viability of replacing Seiko MS in their sealed-for-life barrels. You can read more about that including the MS reference.

 

Link to comment
Share on other sites

Hi @jaycey - I've not worked on a Seiko before but I still read most forum postings no matter what the topic as, assuming I can't answer a particular question, I can still add to my knowledge base!

What I've interpreted from your query and Seiko mainspring postings in general is that if a new mainspring is required then by design it should be a barrel-complete job but getting hold of these is not easy. However with some care it is possible to open a 'sealed barrel' to replace the mainspring.

In this case I would say that a ready reference for springs required per calibre is a great idea! It would be interesting to see what Seiko aficionados think. 

Link to comment
Share on other sites

1 minute ago, WatchMaker said:

Hi @jaycey - I've not worked on a Seiko before but I still read most forum postings no matter what the topic as, assuming I can't answer a particular question, I can still add to my knowledge base!

What I've interpreted from your query and Seiko mainspring postings in general is that if a new mainspring is required then by design it should be a barrel-complete job but getting hold of these is not easy. However with some care it is possible to open a 'sealed barrel' to replace the mainspring.

In this case I would say that a ready reference for springs required per calibre is a great idea! It would be interesting to see what Seiko aficionados think. 

Nail on the head exactly!

 

I mostly head over to the Roland Ranfft movement database when ordering mainsprings (which I replace as a matter of course with every service)

Although he has the Seiko movements in the database, he lists only the part number for the barrel/mainspring complete.

I will probably try and contact him regarding adding to those part numbers with actual spring replacement measurements.

In the meantime though, it would be great to just have 'place' where we can collate the information for him and others to feed off whilst it builds.

 

It will just make life a lot easier for all watchmakers in the future.

Link to comment
Share on other sites

20 hours ago, aac58 said:

WatchGuy has a mainspring database here where with some Seikos, although not all are listed. Sometimes you have to figure out what movement have the exact same spring.

That's perfect & exactly what I was looking for, thanks!

 

Anyone else who's changing Seiko mainsprings, contact WatchGuy if you replace a spring not listed. The 4R36 should be added soon:)

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
    • Now this has happened I bet China or India just to name two will start to produce none genuine parts.  I did. But idiot Boris Johnson failed miserably in his negotiations. The E U stitched up the UK like a kipper. Nigel Farage  offered his help but big head Boris declined. So this is why we are in this mess all because Johnson wasn't clever enough.  
    • Hands up all those who voted to leave the EU 😂, oopsie.  UK has just signed the Hague convention, next year that will provide cross border clout to British courts.
    • Ive heard about that oil before for the lever pins. I found it easy to work on , it didn't have a whole lot of pivot wear but i bit sloppy on the lever cock, i think you have to live with what you have or bin it. Stiff to wind and set ?  Not a cannon pinion issue that has no friction thats made up further back and if I remember the barrel drives the hour wheel. No problem on this one .Let me know when you start it as i have another that donated to this one, i can work alongside you with it, two heads are better than one. 
×
×
  • Create New...