Jump to content

help ID patek philippe watch


Recommended Posts

Hello,

I came across this watch but I know nothing about it and couldn't find anything about this particular watch online, I did learn that this brand is really good and expensive.

do you have any information and is it worth buying?

7e688e13efa77337857787e6cfd09294.jpg

99068cbdd7b617a857e91d5b41cfa3e6.jpg

c852555008883805d78c4af55498f7d3.jpg

Edited by Ammar
Link to comment
Share on other sites

4 hours ago, Ammar said:

so it's experience, I guess I'm gonna have to get scammed a couple of times in order to get this experience ^_^ 

You aren't scammed paying the price of a genuine item, and that is quite rare. So e.g. the watch above is $40, how can one dream that is genuine?!? Buying it you're however an accessory of the crime of counterfeiting.

  • Like 1
Link to comment
Share on other sites

One thing that tips it off (aside from the general look and finish, but that takes some experience) is that Patek does very few watches in stainless steel, and when they do, they do the whole case in stainless. They wouldn't have a precious metal watch with a stainless steel back. Also, stainless Pateks are quite sought after, and easy to Google, so little chance of finding one for a few bucks.

Link to comment
Share on other sites

Here is my take on that watch.

99068cbdd7b617a857e91d5b41cfa3e6.jpg

Dull appearance of case, poor dial quality, cheap hands, fake moonphase, the knurling on the two "crowns" don't match, the crystal is dull and looks like cheap window glass rather than sapphire, the second hand has fallen off, the dial indices are poorly formed and look like plastic, the case back is poorly engraved... the price is stupidly low, the strap looks like it is made from cardboard... save your pennies for something more appealing.

Patek-Philippe.jpg

Compared with this, where everything is sharp.

This is either genuine, or a much higher quality fake (in this case, it is almost certainly genuine), and therein lies the real problem. 

Poor fakes are generally pretty easy to spot, but there are a lot of much higher quality fakes out there.

5327G_001_1.jpg

 

Then there is this. An image straight from the manufacturer's own web site.

Again you can see that everything matches, the dial face looks stunning, the indices are well applied, the whole effect is balanced and even the strap oozes quality.

Edited by AndyHull
  • Like 1
Link to comment
Share on other sites

24 minutes ago, AndyHull said:

Here is my take on that watch.
Dull appearance of case, poor dial quality, cheap hands, fake moonphase, the knurling on the two "crowns" don't match, the crystal is dull and looks like cheap window glass rather than sapphire, the second hand has fallen off, the dial indices are poorly formed and look like plastic, the case back is poorly engraved... the price is stupidly low, the strap looks like it is made from cardboard...

And I've heard that seller has bad breath :biggrin:

These are slam dunks threads really.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...