Jump to content

Recommended Posts

My father in law sent me a Fossil watch my wife and I had given him as a gift. It is a model ME3052 and he told me it was not working. 

 

Upon receiving the watch, I immediately noticed the rotor was loose inside and banging around everywhere. Apparently it came loose after the watch fell. 

 

I opened it up and the rotor had caught in the escapement, damaging the balance spring and wheel. Since the watch had sentimental value, I decided to fix it. 

 

Obviously the movement had no model number or any marking of which I could make out the movement model. I knew it was a Chinese skeleton, of which there are a million models online.  After several days of research and almost giving up, out of pure luck I glanced at the backside of the dial and saw TY2723 marked. I typed it online and bingo! That was the movement model. 

 

I could only find two places which stocked it and decided to go with Esslinger. After the movement arrived I assembled everything. I was almost done when I placed the crown and it wouldn’t go in. After some tinkering it finally went in. I was happy, but when I flipped the case, the winding gear was loose inside the case. Apparently it dislodged when putting in the crown. 

 

I decided to give it a shot and fix it. Mind you I had never taken apart a movement, let alone a skeleton stem assembly. It was difficult and I assembled it wrong several times before finally understanding how everything works. It was good that I had the older movement, cause I lost some tiny screws in the process. I think the hardest part was getting the little spring which drives the clutch lever in place. 

 

Anyways, I put it all together and the watch works great. :)

 

Teaching point: Don’t take on a skeleton movement as your first fix. Hahaha

 

Just wanted to share the experience with you guys, cause I was so happy I was able to fix it. Below are some pictures. 

 

ACA86627-99DB-4394-9740-741152030EA9.jpeg

A0972DFC-8864-4856-94A4-7F2C6376A35F.jpeg

Share this post


Link to post
Share on other sites

Hi you have done well getting that sorted. Its this the start of a new hobby ?  The TY is a seagull chinese movement they are usually based on ETA movements. Unusual to see one of these in a fossil as they usually use the genuine ETA movements. Was the watch a replica or the genuine article. 

Share this post


Link to post
Share on other sites
2 hours ago, watchweasol said:

Hi you have done well getting that sorted. Its this the start of a new hobby ?  The TY is a seagull chinese movement they are usually based on ETA movements. Unusual to see one of these in a fossil as they usually use the genuine ETA movements. Was the watch a replica or the genuine article. 

Hi. Thank you. I am really getting into this hobby. :)  I bought the watch at fossil store so I guess its the real deal. I did read somewhere that Fossil was now using Seagull movements, but I can’t ascertain if this is true. 

Share this post


Link to post
Share on other sites

Hi  If it came from the store it must be genuine, probably Fossil using cheaper chinese units, they will certanly save a bob or two but will it detract from the brand . I have repaired fossil watches and they did use the ETA units. Some of the chinese units are quite acceptable now although the finish is not as good as the ETA.  I noticed you had a problem refitting the stem, On the ETA units pull the stem out to 3rd position then release If not the keyless work displaces and you have to take te dial and hands off to refit might be the same on the clone unit. Not found a tech sheet for it yet.

Share this post


Link to post
Share on other sites
14 minutes ago, watchweasol said:

Hi  If it came from the store it must be genuine, probably Fossil using cheaper chinese units, they will certanly save a bob or two but will it detract from the brand . I have repaired fossil watches and they did use the ETA units. Some of the chinese units are quite acceptable now although the finish is not as good as the ETA.  I noticed you had a problem refitting the stem, On the ETA units pull the stem out to 3rd position then release If not the keyless work displaces and you have to take te dial and hands off to refit might be the same on the clone unit. Not found a tech sheet for it yet.

Thank you for the advice. That’s what happened to me. The kelyless works came undone with the winding gear displaced completely. 

Here is a foto of the backside of the dial with the movement model. 

B57556E1-0A13-46FD-AC2C-BB35D71D405F.jpeg

Share this post


Link to post
Share on other sites

I did this this big boy today and it is ETA-free, but they are reinventing (and patenting) the meca-quartz concept :biggrin:

DSC_0072.thumb.JPG.37b7815500b91d1704ad473b381a67d6.JPG

The mechanical portion moves only the "petite trotteuse", and I even regulated it a little, while feeling a bit stupid in doing so. Amazingly, it takes 25 jewels to accomplish this less than monumental task. 

DSC_0070.thumb.JPG.1c5679d3b42358ffb8e1ee162712c319.JPG

They must have a scarcity of adhesive at the dial factory, because three indexes and the seconds chapter ring had left their place. The minutes hands barely stayed, being made without a tube. 

Share this post


Link to post
Share on other sites
14 hours ago, jdm said:

I did this this big boy today and it is ETA-free, but they are reinventing (and patenting) the meca-quartz concept :biggrin:

DSC_0072.thumb.JPG.37b7815500b91d1704ad473b381a67d6.JPG

The mechanical portion moves only the "petite trotteuse", and I even regulated it a little, while feeling a bit stupid in doing so. Amazingly, it takes 25 jewels to accomplish this less than monumental task. 

DSC_0070.thumb.JPG.1c5679d3b42358ffb8e1ee162712c319.JPG

They must have a scarcity of adhesive at the dial factory, because three indexes and the seconds chapter ring had left their place. The minutes hands barely stayed, being made without a tube. 

Awesome!!  Very cool. A kinetic movement from Fossil. Would like to get one of those. Thanks for sharing!! 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • I got this little beauty  at a swap meet on Sunday.  I changed the battery and still nothing.  I know nothing about quartz. Is there a trick I kneed to know?  Is it worth taking down to be repaired?  Should I look for an ETA movement to put inside?  It does have the gold matching band in good condition.
    • So jdm if you want I can mail you the watch of your dreams.
    • When I was in the armoured corps they said “when I doubt Pit Out” aka go to sleep. Sent from my iPhone using Tapatalk Pro
    • Thanks for the reference. I may have that book. Sent from my iPhone using Tapatalk Pro
    • Thank you AndyHull and JerseyMo for responding with really helpful instructions!  You guys rock!  i have to get some rodic to help hold these two little mini-monsters in place. I was trying to use a small bit of sticky-tack but it didn't hold well enough.  I would get the screw into position but it would fall over when the screwdriver touched the screw.   For the 24 movement that still has the broken screw end in it, I will try to get that out after I get the lever and screw installed in my working 24.  And yes, I will install the crown/stem AFTER I have the lever and screw in place on the plate. Again, thanks for your help- i really appreciate it!!!  Will let you know when I get things back together.
×
×
  • Create New...