Jump to content

Help with balance jewels / springs for novice


Sberry

Recommended Posts

I've (99%) completed the WRL level 2 course. My ST36 movement went back together smoothly until I tried to refit the upper balance jewel. I've now learned a lot about tiny parts flying away, and also how difficult it is to find those parts, and finally that they are generally unavailable to buy separately if you do lose them.

I put that movement into a bag and set it aside and decided to move onto another watch - a Slava 2428 I found on ebay in poor working condition. Again everything went smoothly, rewarding success and progress and confidence with help from ratfacegit videos on youtube, until I came again to the balance jewel and springs. Luckily, after googling after previous flying parts issues for tips, I began draping a clear piece of plastic film over my work and this worked really well to keep flying parts from flying too far. I was able to do a satisfying job of oiling the jewel and placing the capstone on the lower bearing cup. When it came to replacing the tri-legged spring in the Russian movement I sank at least 2 hours into trying to fit it in place with no success and found it incredibly frustrating. I'm paused again at this step. I do feel like I'm growing skills with this tweezer work, but I find frustration is hurting my motivation.

I have a lighted optivisor with a 3.5x power lens, with an optional 2.5x power loop I can slide in front of one eye. This feels like a minimal, possibly not enough, level of magnification when it comes to the balance jewel work. I invested in nice screwdrivers, swiss tweezers - I just can't seem to coordinate these springs.

1. When you work on servicing balance jewels is there a level of magnification that works best? Should I invest in a higher magnification eyeloop (10X?) just for that work?

2. In collective experience, is servicing the balance jewels a universal challenge for new watchmakers? Nothing else has really derailed me.

3. I've considered trying to service a few more near-junk watches without servicing the balance jewel disassembled, but doing a caveman job of cleaning and oiling it. Do you guys run into situations where you've made this decision and had success? I've seen a couple of videos where the watchmaker chooses not to service a shock jewel because the springs are irreplaceable and known to break. I definitely don't want anyone to endorse bad craftsmanship but wondering about situations where you've made compromises.

Overall, very much enjoying learning. Mark's videos have been a great structured start.

 

IMG_5793.HEIC

Link to comment
Share on other sites

In cases of hard to replace jewels, I prefered this method over no clean option.

Remove balance complete, springs ..even regulating arm. Clean, even brush some parts.

Spread a large sheet of white material on the floor. On which I work on balance bridge.

Use bare hands and all it takes to instal the jewel assembly and springs back on, I do not worry about hand- parts contact at this stage.

Rinse. Oil through chaton hole, oil pivots as well.instal.

Meanwhile the balance complete is taking a bath in lighter fluid, shake the bottle very slowly.

You have cleaned all, the jewel, beneath the arms. Rinsed , got a chance to see a full view of hairspring coils, endcurve, etc.

I have no doubt you will find " not worrying about hand-parts contact, drastically eases working and improves your control over the task and enhances results.

 

 

 

 

  • Like 1
Link to comment
Share on other sites

Certain types of shock setting are difficult for all to handle.  The typical incabloc is not difficult as long as you DO NOT unseat the shock spring.  Then things can get sticky.  Kiff shock spring are a PITA unless you have the Kiff seating tool.  Your description sounds like a Kiff or some variant thereof.


Good luck and don't give up.  We all have our days.


RMD

Edited by rduckwor
  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...


  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
    • Does anyone knows what size case a need for a dial diameter 20.60mm?
    • Sounds like the story with my Rolex. Poor (expensive) job done by an official Rolex dealer with an "in-house" watchmaker, hence I learned watchrepair and did the servicing myself. Same story as I learned with the Omega 861, again poor job by an "in-house" watchmaker by an official Omega dealer. Once your watch goes through that back-door, you have no idea what is going to happening to it 🫣   Quite nice that they sent back the parts which had been replaced !
    • yes that's definitely not right at all. I have a picture one of my friends has a Omega coaxial there was having issues to lose asking me where he should send it. As that's a specialty watch I suggested the service center. When he got it back he sent me a picture so the replace the dial as you can see the hands the mainspring barrel and I think the price was really quite decent considering all the stuff they can replace. So I do know they do change the barrels but the other person I worked at the service center when I would ask questions and unfortunately I can't remember all the answers. I think a lot of the changing a parts is at the discretion of the watchmaker. Plus I don't know enough about the chronographs and whether that would be considered a vintage watch? I take some of the vintage watches may have been sent directly to Switzerland or another service center. Obviously with a watch like the one down below they probably have a infinite supply of parts is its relatively modern vintage stuff becomes more interesting even the watch companies don't have necessarily infinite supply of parts. But no matter what the watch shouldn't disintegrated six months that's definitely an issue.        
    • glad it worked out, those ESA movements are obsolete but new old stock is still out there, now that you know the make/model you could also do a cross reference to see if something more current would line up with the dial feet and hands...for future use if needed 👍
×
×
  • Create New...