Jump to content

It's the little things in life


Recommended Posts

My wife has had a jumbo size jar of pickles of the bench for the last 2 months that has defied all efforts to open it.

Bought a new Silicone jar opener, made no difference.

Holding the jar at 45 degrees and slapping the bottom of the jar to use the 'water hammer' effect didn't work.

Me holding the jar and my son trying to open it didn't work.

Heating the jar lid with me holding the jar and my son trying to open it didn't work.

After coming home tonight from the pub I could see my wife had tried to open it again without success.

I gave up and searched the web for how to open stuck pickle jars and one suggestion was use a bottle opener on the side of the lid.

I very carefully used my best bottle opener (Hand forged by a blacksmith) on the edge of the lid and 'pop' went the lid without the lid being damaged.

The jar is now open after 2 months of trying, is there anything the web can't help you with?

 

:D

  • Like 2
Link to comment
Share on other sites

 Air needs to get in, since the jar has to a good extent been vaccumed, it is heated and the sealer lid is preesed on, as it cools a relative vaccum inside creates suction if you will, that is like strong  pressure from the outside pressing on the lid.

Proper proceesing is of high significance, on jar, bottling and canning lines alike, since in addition to the processed content, the consumer health and producers repution is on the line, processed food safety is No one concern in modern societies of today. 

Other techniques in industry is to preesurize the inside with like nitrogen gas, inerst to the food stuff. Which is probably used in your coke and beer bottles, depending on the country and regulations. 

You can also tap on the rim of the lid, to disfigure the lid enough for air to get in.

Best

Edited by Nucejoe
Not from internet, imported bottling line for son in law, kronas of Germany.
Link to comment
Share on other sites

The best solutions are normally found after a visit to the pub.

I've watched enough episodes of Morse to know that there's not a problem known to man that a beer can't help to solve.[emoji3]

Sent from my moto g(6) play using Tapatalk

  • Haha 1
Link to comment
Share on other sites

Seafoam!  In the tank and the aerosol can into the fuel rail.  (If you can get Seafoam where you are).  Also freed the stuck valve on my '93 Pathfinder and their Deep Creep penetrating oil is the only thing I use on anything from tractors to rusted motion works!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
    • this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.  
    • OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
×
×
  • Create New...