Jump to content

Using a crystal press

AP1875

By AP1875
in Tools & Equipment

 Share

Recommended Posts

AP1875 WRT Addict

AP1875

Posted
Posted

I picked up a Robur press on ebay it came with the T31 die set. It was a fairly decent price. So I thought I'd give it a go considering the $10 one I've been using from ebay doesn't press straight. 

I just want to check what I'm using it for and how I'm using it is correct. 

The watch I want to fit a new crystal to has the following construction - crystal held in place with a plastic ring, the crystal is the fixed by pushing the steel bezel over it. 

 

So

I put a metal die on the bottom of the press that the caseback will sit in and cover with a cloth to prevent damage. 

On the top I select a die that just fits around the crystal and rests on the bezel? 

The best fit die still has a little bit of room on both the bottom and top. 

 

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Lay the case on a suitable flat bed die depends on the size of the case. Pick one of the cupped dies so it just fits over the glass, that goes into the top. Screw down watching that the cup is even all round, you  quite often hear a sound as the glass is pushed home. Remove case  and check to see that the glass is even around in side the case.   

The Robur press is one of the best for fitting tension ring glasses. 

  • Like 2
Link to comment
Share on other sites
AP1875 WRT Addict

AP1875

Posted
  • Author
Posted
3 hours ago, oldhippy said:

Lay the case on a suitable flat bed die depends on the size of the case. Pick one of the cupped dies so it just fits over the glass, that goes into the top. Screw down watching that the cup is even all round, you  quite often hear a sound as the glass is pushed home. Remove case  and check to see that the glass is even around in side the case.   

The Robur press is one of the best for fitting tension ring glasses. 

ahh ok i will use the flat die. I guess the only difference between the watch i'm swapping the glass on is you have to press down on the bezel and not the glass. The glass is already in position, the bezel holds it there.

What are these black dies for? They look like they could snap very easily.

Link to comment
Share on other sites
AP1875 WRT Addict

AP1875

Posted
  • Author
Posted (edited)
3 minutes ago, oldhippy said:

What are these black dies for? They look like they could snap very easily. A photo would help.:D

Sorry forgot to send the link.

This is the set i have. I got the press and dies for less than the cost of the dies alone, way out of my budget otherwise.

https://www.cousinsuk.com/product/die-set-robur

Would you use this press for a ceramic bezel?

Edited by AP1875
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

The blacks are to be used for the bass when you fit low dome glasses.  When you put the glass in the top die it causes the glass to bend and become a little smaller, it’s the shape of them that also helps when pressure is applied. That one flat bed die, you will find you will use that a lot when fitting tension ring glasses   

Would you use this press for a ceramic bezel? If you have a die that will go over and press it right down on the case then yes. Fitting those things you need ever pressure and this tool will do the trick. 

Link to comment
Share on other sites
AP1875 WRT Addict

AP1875

Posted
  • Author
Posted
26 minutes ago, oldhippy said:

The blacks are to be used for the bass when you fit low dome glasses.  When you put the glass in the top die it causes the glass to bend and become a little smaller, it’s the shape of them that also helps when pressure is applied. That one flat bed die, you will find you will use that a lot when fitting tension ring glasses   

Would you use this press for a ceramic bezel? If you have a die that will go over and press it right down on the case then yes. Fitting those things you need ever pressure and this tool will do the trick. 

Thank you for sharing your wisdom. I just tried it on a ceramic and it was so much easier than my last press.

Does your Robur have a slight bit of play in the shaft or is it completely solid? I can wiggle this one ever so slightly but apparently it has had new shaft fitted.

 

Link to comment
Share on other sites
vinn3 Distinguished Member

vinn3

Posted
Posted

  I bought a well used (destructively)  case closer at a watch mart.   all the black dyes were broken or glued.   it had the cardboard box and all the instructions.  "the price was right".   I made aluminum cups for each watch to be closed.  vin

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.   I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • RichardHarris123
      Intro

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • oldhippy
      Without Our Forum

      By oldhippy · Posted

      Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
    • oldhippy
      Intro

      By oldhippy · Posted

      Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.    
×
×
  • Create New...