Jump to content

Using a crystal press


AP1875

Recommended Posts

I picked up a Robur press on ebay it came with the T31 die set. It was a fairly decent price. So I thought I'd give it a go considering the $10 one I've been using from ebay doesn't press straight. 

I just want to check what I'm using it for and how I'm using it is correct. 

The watch I want to fit a new crystal to has the following construction - crystal held in place with a plastic ring, the crystal is the fixed by pushing the steel bezel over it. 

 

So

I put a metal die on the bottom of the press that the caseback will sit in and cover with a cloth to prevent damage. 

On the top I select a die that just fits around the crystal and rests on the bezel? 

The best fit die still has a little bit of room on both the bottom and top. 

 

Link to comment
Share on other sites

Lay the case on a suitable flat bed die depends on the size of the case. Pick one of the cupped dies so it just fits over the glass, that goes into the top. Screw down watching that the cup is even all round, you  quite often hear a sound as the glass is pushed home. Remove case  and check to see that the glass is even around in side the case.   

The Robur press is one of the best for fitting tension ring glasses. 

  • Like 2
Link to comment
Share on other sites

3 hours ago, oldhippy said:

Lay the case on a suitable flat bed die depends on the size of the case. Pick one of the cupped dies so it just fits over the glass, that goes into the top. Screw down watching that the cup is even all round, you  quite often hear a sound as the glass is pushed home. Remove case  and check to see that the glass is even around in side the case.   

The Robur press is one of the best for fitting tension ring glasses. 

ahh ok i will use the flat die. I guess the only difference between the watch i'm swapping the glass on is you have to press down on the bezel and not the glass. The glass is already in position, the bezel holds it there.

What are these black dies for? They look like they could snap very easily.

Link to comment
Share on other sites

3 minutes ago, oldhippy said:

What are these black dies for? They look like they could snap very easily. A photo would help.:D

Sorry forgot to send the link.

This is the set i have. I got the press and dies for less than the cost of the dies alone, way out of my budget otherwise.

https://www.cousinsuk.com/product/die-set-robur

Would you use this press for a ceramic bezel?

Edited by AP1875
Link to comment
Share on other sites

The blacks are to be used for the bass when you fit low dome glasses.  When you put the glass in the top die it causes the glass to bend and become a little smaller, it’s the shape of them that also helps when pressure is applied. That one flat bed die, you will find you will use that a lot when fitting tension ring glasses   

Would you use this press for a ceramic bezel? If you have a die that will go over and press it right down on the case then yes. Fitting those things you need ever pressure and this tool will do the trick. 

Link to comment
Share on other sites

26 minutes ago, oldhippy said:

The blacks are to be used for the bass when you fit low dome glasses.  When you put the glass in the top die it causes the glass to bend and become a little smaller, it’s the shape of them that also helps when pressure is applied. That one flat bed die, you will find you will use that a lot when fitting tension ring glasses   

Would you use this press for a ceramic bezel? If you have a die that will go over and press it right down on the case then yes. Fitting those things you need ever pressure and this tool will do the trick. 

Thank you for sharing your wisdom. I just tried it on a ceramic and it was so much easier than my last press.

Does your Robur have a slight bit of play in the shaft or is it completely solid? I can wiggle this one ever so slightly but apparently it has had new shaft fitted.

 

Link to comment
Share on other sites

  I bought a well used (destructively)  case closer at a watch mart.   all the black dyes were broken or glued.   it had the cardboard box and all the instructions.  "the price was right".   I made aluminum cups for each watch to be closed.  vin

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • that band is old as stated, there is a kit that pops up from time to time on selling sites for the repair of these type bands, some of this type are adjustable on a few links, one adjustable type allows you to align the round opening in the expansion slit [like yours] with the rivet to separate, but if yours won't come out then the rivet head is too big and will have to be done with some rivet removal and replacement, I suppose if you could make/optain the correct rivets that one could alter the said band, the tops/caps do lift off after raising the tabs....  
    • This is a watch from a friend who sent it to a neighborhood watchmaker for a battery change. It came back with the watch stem in a ziplock bag and the dial skewed 20°. The watchmaker told him that the stem was faulty and the watch cannot be repaired. I opened up the watch and found that one dial foot was broken off and still stuck in the movement, while the other was bent until it was flat against the dial. The stem could be inserted but it couldn't be pulled out to quickset and time adjusting positions. I did a full disassemble, cleaned and oiled the movement. But when it put in the battery, the second hand runs super fast. Like it gains 30 mins every hour. Any advice on fixing this problem? TIA.
    • I determined that the balance staff is rotating, not the roller table, so my second attempt at riveting was unsuccessful. I have ordered a new balance staff and will take measurements when it arrives. The balance staff i originally ordered (and now reordered) was specified as: Replacement balance staff: (A. Schild Caliber 984 1002 1021 1124 Original Balance Staff Part 723) so it should be correct. Measurements: (see pic below for terminology) xxxyy is a place holder until the new balance staff arrives. Lower pivot: Old - .08 mm New - xxxyy Lower pivot to balance seat: Old - 1.53 mm New - xxxyy Roller shoulder: Old - .42 mm New - xxxyy Hub: Old - xxxyy New - xxxyy Balance shoulder: Old - .86 mm New - xxxyy Collet shoulder: Old - .56 mm New - xxxyy Upper pivot: Old - broken New - xxxyy
    • Hello and welcome from Leeds.  We're here to help. 
    • I was just about to adk that, probably they have unnecessary waiting lists to make their watches appear more exclusive than they actually are.
×
×
  • Create New...