Jump to content

Longcase clock

Johncross

By Johncross
in All Things Clocks

 Share

Recommended Posts

oldhippy Distinguished Member

oldhippy

Posted
Posted

You need to let the pendulum bob down. It should have a nut under neath the bob. Remember clocks that have pendulum movements. To make it gain higher the pendulum, to make it lose time lower the pendulum.

I would like to see a few photos of the movement, dial and case if possible. 

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi John  As Old Hippy says either move the rating nut up to make it go faster or down to slow it down, But first of all make sure its in beat (even tick and tock) then set the rating if all is ok.  I take it when you serviced it you checked all the pivots and pivot holes for wear and re-bushed any worn ones.  Again some photos of the movement would be appreciated.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      Just a note for those who come searching for information on this topic in the future.  I did eventually find the Mark's video on how to replace these springs, as someone observed, he does in fact make the replacement look easy.  (It actually is relatively easy once you have the knack of it.) If you're enrolled in one of Mark's online courses, the demonstration of how to replace this spring is in the Bonus Videos section of his course site, and is called "C2B1 – Sea-Gull Style Shock Springs".
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      If the metal was twice as thick, it wouldn't snap so easily.  The thickness is governed by the space available so you can't use thicker metal.  If you glued two pieces together, the likelihood of snapping would be reduced.  That's my theory anyway, could be wrong. 
    • JohnR725
      Pocket watch escape wh

      By JohnR725 · Posted

      there are various approaches to learning watch repair. A lot of people want to jump right in and every single watches something to be repaired restored. But other times like this it's disposable it's here for you to learn and when you're through learning you throw it away. yes you definitely should try this you have a learning movement you need to learn and the best way to learn is by doing something.
    • nevenbekriev
      Pocket watch escape wh

      By nevenbekriev · Posted

      Sorry, the friction will be so great that the wheel will barely turn, if the movement will start at all, the amplitude will be verry lo.
    • Bonefixer
      Pocket watch escape wh

      By Bonefixer · Posted

      If I can’t re-pivot the wheel, the logical thing to do is to descend the pivot hole.  Plan is to either stick a suitably sized hole jewel (from a barrel bridge or something) or fashion a blob of epoxy on the underside of the escape wheel cock so the wheel sits on its one pivot on the base plate and the staff with the broken off pivot (which I’ll polish as best as I can) becomes the upper pivot. As long as it doesn’t foul the 4th wheel it should work? I know it’s a bodge job, and if this were a rare movement, or belonged to someone else I would not do this. I’m just interested to see if I can get the thing to run. 
×
×
  • Create New...