Jump to content

New Video - Vintage Omega 30T2 (1940's Military Watch) With Broken Impulse Jewel

Mark

By Mark
in Watch or Horology Related Videos

 Share

Recommended Posts

Mark Distinguished Member

Mark

Posted
Posted

Just uploaded a new video. This one is one of my favourites, an Omega Military watch from the mid to late 40s. It had a broken balance staff, impulse jewel and the pivot on the centre wheel had a groove worn into it.

 

I didn't film the lathe work but managed to get quite a bit under the camera.

 

I hope it's useful to someone.

 

post-1-0-79536100-1419079855_thumb.jpg

 

Some pics:

 

post-1-0-95293900-1419082175_thumb.jpgpost-1-0-49698100-1419082176_thumb.jpgpost-1-0-00010600-1419082177_thumb.jpgpost-1-0-41873600-1419082177_thumb.jpgpost-1-0-89665500-1419082177_thumb.jpgpost-1-0-48697200-1419082178_thumb.jpgpost-1-0-97044800-1419082178_thumb.jpgpost-1-0-43095000-1419082179_thumb.jpgpost-1-0-99983600-1419082179_thumb.jpgpost-1-0-43249100-1419082180_thumb.jpgpost-1-0-12062600-1419082206_thumb.jpgpost-1-0-69137300-1419082206_thumb.jpgpost-1-0-19307200-1419082207_thumb.jpgpost-1-0-66042400-1419082207_thumb.jpgpost-1-0-23566900-1419082208_thumb.jpgpost-1-0-66467600-1419082208_thumb.jpgpost-1-0-06066800-1419082209_thumb.jpgpost-1-0-41001900-1419082209_thumb.jpg

  • Like 5
Link to comment
Share on other sites
cdjswiss WRT Addict

cdjswiss

Posted
Posted

Another fine video with an excellent lesson on replacing the impulse pin. Thanks.

A question: when starting from a broken-off pin how do you judge the initial position of the new jewel with respect to the roller? Is that just experience or is  there a rule?

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
  • Author
Posted

The jewel cannot foul the guard pin on the pallets. And the crescent notched into the roller is for the guard pin to pass. So, naturally, the bottom of the jewel must be above the crescent.

Hope that makes sense.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Hi Mark,

 

I believe this is one of the best videos ever concerning the quality and nearness of the takes! The contents is unbelievable just like the other ones, this simply highlights it with amazing quality. I learned a lot from it continuing a learning curve only made possible by your excellent videos and forum.

 

May I ask, the plate you use to heat the Shellac -- which has appeared before in your videos -- is it something of your own manufacture or is it available for sale elsewhere? Since I got my staking tools I've been collecting all sort of goodies to work on (just waiting for a good time and some jewels) and foresee doing some of the same Shellac/heat thing you so masterly do on your videos.

 

Thank you for the info in advance and many more thanks for the excellent Christmas gift that this video represents to us. Your labor of love is deeply appreciated.

 

Cheers,

 

Bob

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted (edited)

The plate Mark is using is I suspect what I use which is an old Clock movement plate. Another point worth noting is I attended a presentation by a guy who repairs and services watches for a living at a Kent BHI. During the meeting it was asked if you can not purchase  a replacement pivot that is scored on say a Rolex what is the alternative. The guy said it is quite acceptable to remove the score from the pivot on a lathe & re-jewel with a jewel that has a smaller internal hole. Exactly as Mark does in this excellent vid.

Edited by clockboy
  • Like 1
Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
  • Author
Posted

Thanks guys.

 

The brass plate is made by myself - just a rough job from some brass sheeting.

 

The holes are useful for blueing screws. The channel slot is useful for tempering newly made stems after hardening.

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Thank you Mark, I appreciate the information. Do you recommend specific dimensions and type/thickness of brass sheeting or you just go by the spur (needs) of the moment, so the holes and other features are added accordingly?

 

Cheers,

 

Bob

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I finally got some time to watch Marks latest horological production. As usual a quality production that I enjoyed immensely. The more I learn, the more I wish I had been involved with horology years ago. At least now being retired, I can devote a lot more time to it.

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
  • Author
Posted

Thank you Mark, I appreciate the information. Do you recommend specific dimensions and type/thickness of brass sheeting or you just go by the spur (needs) of the moment, so the holes and other features are added accordingly?

 

Cheers,

 

Bob

 

It was just a scrap piece of brass lying around, drilled a few holes and filed a channel :D

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
  • Author
Posted

... and I believe you are using a new microphone too  .... make you sound very debonair :)

 

Cheers mate - was hoping to attract some female viewers with my debonair voice. So far it's not working :D

Link to comment
Share on other sites
rustycolt Watch Enthusiast

rustycolt

Posted
Posted

What a genuine privilege it is to be able to watch such skilled work take place. Thank you Mark for sharing your talent with us! 

 

I'm sure the debonair voice will bring the lady watch groupies out of hiding. You should have no trouble cornering that market  :rock:

Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...