Jump to content

New Video - Vintage Omega 30T2 (1940's Military Watch) With Broken Impulse Jewel

Mark

By Mark
in Watch or Horology Related Videos

 Share

Recommended Posts

Mark Distinguished Member

Mark

Posted
Posted

Just uploaded a new video. This one is one of my favourites, an Omega Military watch from the mid to late 40s. It had a broken balance staff, impulse jewel and the pivot on the centre wheel had a groove worn into it.

 

I didn't film the lathe work but managed to get quite a bit under the camera.

 

I hope it's useful to someone.

 

post-1-0-79536100-1419079855_thumb.jpg

 

Some pics:

 

post-1-0-95293900-1419082175_thumb.jpgpost-1-0-49698100-1419082176_thumb.jpgpost-1-0-00010600-1419082177_thumb.jpgpost-1-0-41873600-1419082177_thumb.jpgpost-1-0-89665500-1419082177_thumb.jpgpost-1-0-48697200-1419082178_thumb.jpgpost-1-0-97044800-1419082178_thumb.jpgpost-1-0-43095000-1419082179_thumb.jpgpost-1-0-99983600-1419082179_thumb.jpgpost-1-0-43249100-1419082180_thumb.jpgpost-1-0-12062600-1419082206_thumb.jpgpost-1-0-69137300-1419082206_thumb.jpgpost-1-0-19307200-1419082207_thumb.jpgpost-1-0-66042400-1419082207_thumb.jpgpost-1-0-23566900-1419082208_thumb.jpgpost-1-0-66467600-1419082208_thumb.jpgpost-1-0-06066800-1419082209_thumb.jpgpost-1-0-41001900-1419082209_thumb.jpg

  • Like 5
Link to comment
Share on other sites
cdjswiss WRT Addict

cdjswiss

Posted
Posted

Another fine video with an excellent lesson on replacing the impulse pin. Thanks.

A question: when starting from a broken-off pin how do you judge the initial position of the new jewel with respect to the roller? Is that just experience or is  there a rule?

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
  • Author
Posted

The jewel cannot foul the guard pin on the pallets. And the crescent notched into the roller is for the guard pin to pass. So, naturally, the bottom of the jewel must be above the crescent.

Hope that makes sense.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Hi Mark,

 

I believe this is one of the best videos ever concerning the quality and nearness of the takes! The contents is unbelievable just like the other ones, this simply highlights it with amazing quality. I learned a lot from it continuing a learning curve only made possible by your excellent videos and forum.

 

May I ask, the plate you use to heat the Shellac -- which has appeared before in your videos -- is it something of your own manufacture or is it available for sale elsewhere? Since I got my staking tools I've been collecting all sort of goodies to work on (just waiting for a good time and some jewels) and foresee doing some of the same Shellac/heat thing you so masterly do on your videos.

 

Thank you for the info in advance and many more thanks for the excellent Christmas gift that this video represents to us. Your labor of love is deeply appreciated.

 

Cheers,

 

Bob

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted (edited)

The plate Mark is using is I suspect what I use which is an old Clock movement plate. Another point worth noting is I attended a presentation by a guy who repairs and services watches for a living at a Kent BHI. During the meeting it was asked if you can not purchase  a replacement pivot that is scored on say a Rolex what is the alternative. The guy said it is quite acceptable to remove the score from the pivot on a lathe & re-jewel with a jewel that has a smaller internal hole. Exactly as Mark does in this excellent vid.

Edited by clockboy
  • Like 1
Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
  • Author
Posted

Thanks guys.

 

The brass plate is made by myself - just a rough job from some brass sheeting.

 

The holes are useful for blueing screws. The channel slot is useful for tempering newly made stems after hardening.

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Thank you Mark, I appreciate the information. Do you recommend specific dimensions and type/thickness of brass sheeting or you just go by the spur (needs) of the moment, so the holes and other features are added accordingly?

 

Cheers,

 

Bob

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I finally got some time to watch Marks latest horological production. As usual a quality production that I enjoyed immensely. The more I learn, the more I wish I had been involved with horology years ago. At least now being retired, I can devote a lot more time to it.

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
  • Author
Posted

Thank you Mark, I appreciate the information. Do you recommend specific dimensions and type/thickness of brass sheeting or you just go by the spur (needs) of the moment, so the holes and other features are added accordingly?

 

Cheers,

 

Bob

 

It was just a scrap piece of brass lying around, drilled a few holes and filed a channel :D

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
  • Author
Posted

... and I believe you are using a new microphone too  .... make you sound very debonair :)

 

Cheers mate - was hoping to attract some female viewers with my debonair voice. So far it's not working :D

Link to comment
Share on other sites
rustycolt Watch Enthusiast

rustycolt

Posted
Posted

What a genuine privilege it is to be able to watch such skilled work take place. Thank you Mark for sharing your talent with us! 

 

I'm sure the debonair voice will bring the lady watch groupies out of hiding. You should have no trouble cornering that market  :rock:

Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      Sounds great! And yes, I would use grease for the keyless as well although treating the parts with epilame would make the grease less likely to spread in the long run. Not critical but won’t hurt. My current strategy is to epilame treat all parts getting in contact with oil or grease.
    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.       I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • RichardHarris123
      Intro

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • oldhippy
      Without Our Forum

      By oldhippy · Posted

      Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
×
×
  • Create New...