Jump to content
  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By DouglasSkinner
      I have an old Waltham pocket watch movement which is missing the impulse pin (roller jewel).  I have a limited number of actual jewels and since this is just a practice movement I thought I'd try to make one out of brass.  I've seen this several times in old pieces--usually a very sloppy job.  So I got some brass stock of the same diameter as the "D" in the roller table, filed it and burnished it to a high gloss.  Then I took a small, very fine diamond file and filed it half flat to form the "D"  I then polished the face using progressively finer sandpaper on a steel block.  This works fine--so far!  Problem is separation of the piece from the stock.  Again I used a small cutting file to do this but it doesn't leave the end very pretty.  So what I've done so far is to fit the good end into the roller table.  I then plan to shellac it in place and see if I can very carefully adjust the length and clean up the end.  Has anyone done this before?  Any suggestions as to how best to do it?  
    • By arkobugg
      Cheers mates!!
      Had to get new winding stem to an Omega cal. 342 , beacuse not original crown.
      Got an replacement from Ronda, but does not fit.
      Tried to fit the stem yesterday, but Im not able to get in in right in the movment.   The original just go right in every time, but the new Ronda stem will not go properly in.   Are there anyone that have some ide why this not fit?   Can the notch in the stem where I have put red arrow have somthing todo with this??   Its slightly smaller on the Ronda stem...  se photo  

    • By arkobugg
      Cheers Mates!
       
      Working on a Omega Cal. 613, have done service, and watch performs well on the time-grapher, but when put dial and hand on, I can see that the
       
       
       
       
    • By Harmines
      Hello all
      i wonder if anyone could offer some advice. I have an Omega seamaster 1345 quartz day date. Working well. However it seems the date is stuck (as shown in pictures) i know the push button at the 4 o clock position is meant to filter through the date? However when pushed in nothing seems to happen. As a result of this the watch works fine but only up untill 11pm it doesnt turn over to midnight and therefor change the day or date. Minute hand works perfectly but it seems i have to change the hour position every morning.
      when i turn the crown, hour hand moves fune and after the 12 o clock position changes the day, but date does not moth along with it.
      anyone know how i can resolve this safely without removing too many parts of the movement? 
      Many thanks




  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • Just as a curiousity here is the tools recommended by ETA the bearing tool and some others..
    • Thanks all but the price of the Horotec tool is a bit prohibitive... I have managed to free it with a very sharp piece of peg wood in one of the cut outs and push it round..The bearing is OK its just that the balance needs some work and you cant remove it with the rotor in place.
    • To remove the beaing you need a special tool but just to remove the rotor you just take of the three screws holding the automatic mechanism, turn it around and unscrew three small screws on the underside and the rotor gets loose.. Could take a couple of shots for you if you wish..
    • Blimey, I see what you mean. What you've got there would appear to be two French-made Framelac pin-levers, a movement maker about which very little seems to be recorded. I've attached an image from the Uhrforum.de of the jewelled-lever FR 304 for comparison of the bridge configuration (similar) and the shape of the balance cock (identical). 
    • Strange. And the setting lever is turned the right way up? Can't see on the picture. 
×
×
  • Create New...