Jump to content
  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By DouglasSkinner
      I have an old Waltham pocket watch movement which is missing the impulse pin (roller jewel).  I have a limited number of actual jewels and since this is just a practice movement I thought I'd try to make one out of brass.  I've seen this several times in old pieces--usually a very sloppy job.  So I got some brass stock of the same diameter as the "D" in the roller table, filed it and burnished it to a high gloss.  Then I took a small, very fine diamond file and filed it half flat to form the "D"  I then polished the face using progressively finer sandpaper on a steel block.  This works fine--so far!  Problem is separation of the piece from the stock.  Again I used a small cutting file to do this but it doesn't leave the end very pretty.  So what I've done so far is to fit the good end into the roller table.  I then plan to shellac it in place and see if I can very carefully adjust the length and clean up the end.  Has anyone done this before?  Any suggestions as to how best to do it?  
    • By arkobugg
      Cheers mates!!
      Had to get new winding stem to an Omega cal. 342 , beacuse not original crown.
      Got an replacement from Ronda, but does not fit.
      Tried to fit the stem yesterday, but Im not able to get in in right in the movment.   The original just go right in every time, but the new Ronda stem will not go properly in.   Are there anyone that have some ide why this not fit?   Can the notch in the stem where I have put red arrow have somthing todo with this??   Its slightly smaller on the Ronda stem...  se photo  

    • By arkobugg
      Cheers Mates!
       
      Working on a Omega Cal. 613, have done service, and watch performs well on the time-grapher, but when put dial and hand on, I can see that the
       
       
       
       
    • By Harmines
      Hello all
      i wonder if anyone could offer some advice. I have an Omega seamaster 1345 quartz day date. Working well. However it seems the date is stuck (as shown in pictures) i know the push button at the 4 o clock position is meant to filter through the date? However when pushed in nothing seems to happen. As a result of this the watch works fine but only up untill 11pm it doesnt turn over to midnight and therefor change the day or date. Minute hand works perfectly but it seems i have to change the hour position every morning.
      when i turn the crown, hour hand moves fune and after the 12 o clock position changes the day, but date does not moth along with it.
      anyone know how i can resolve this safely without removing too many parts of the movement? 
      Many thanks




  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • Alternatively you could use tinned copper wire.It solders very easily.
    • Pierre Chevelle. gran sport 150. My father got it for me about 50 years ago.A cigar smoker ,he got it in exchange for cigar bands from the Phillies he smoked.Still have it. I just installed a new crystal.It awaits a clean lube and adjust.
    • Dear all, I recently had the pleasure of finding a damaged hairspring needing care. My first! It’s an inexpensive orient watch, gaining 20 minutes a day. I am taking Mark’s fault finding course, and have other inexpensive hairsprings to practise with. I also got some vintage tools I’d love to use. Until now for me levellers were only the Oliver Cromwell people, but ebay never ceases to surprise... I could pass the first stages of correcting the coil, with two tweezers. But could not find a use for the vintage tools. Could you help me to figure it out?  Picture 1 is the bent hairspring  picture 2 and 3 the box of tas levellers picture 4 is the hairspring suffering under my tweezers now picture 5 shows the tip of the tools picture 6: from De Carle. Would this be the purpose of the levellers? The overcoil? 
    • my first running watch was an Wyler squire.  i wore the case out,  the mvt. would fall out at work.  i still have it and another with a similar case.   vin
    • First watch was a Kered    from Shepherds of the shambles in York, alas no longer in business. The plus side is I still have the watch it was a 21st birthday pressie, and even better it still ticks  54 years later although the dial has a water mark ,    I even wore it playing cricket for 12 years. 
×
×
  • Create New...