Jump to content

Proper Way To Install Balance Complete.


Recommended Posts

I have never taken classes or any formal Watchmaking training, but have been at it a very long time. However, today as I was installing a Balance as I've done many times before I realized that I had no set way of doing so and don't know if there is a proper procedure.

I seat the wheel and then twist the movement about 90° and the seat the balance cock(bridge). Is there a specific direction to rotate movement while installing the bridge? Should I coil or uncoil hairspring when twisting, or does to matter?

Regards,

David

Link to comment
Share on other sites

The way I was taught (by trained watchmakers, but I myself am not qualified) was in line with what you are describing. In detail;

1. set the pallet fork against the left-hand banking pin. This ensures that the impulse jewel enters the fork.

2. introduce the balance assembly with the balance cock at least 90 degrees anticlockwise of its final position

3. seat the lower balance pivot without disturbing the pallet fork

4. rotate the balance cock clockwise (or the movement anticlockwise, whilst holding the cock still) into its final position, and rest gently on top of the balance wheel

5. locate the upper pivot in the jewel. The balance begins to swing

6. Drop the screw in. Hold the cock steady with a piece of pegwood or a toothpick and slowly tighten the screw.

7. If the balance stops swinging, immediately back off the screw.

I guess you could also reverse the directions described in steps 1 to 4. At no stage are you coiling or uncoiling the hairspring.

  • Like 2
Link to comment
Share on other sites

If stripped down to mainplate, I instal the balance back on. Check and do all the work, namely end shake, free balance wheel movement, level  the hairspring, make sure I get concentric coil, balance wheel to come to rest at the right angular position( impulse in beat) etc. I will then remove and proceed. 

I do all such repairs and work before cleaning. 

Observation you list sounds good to me.

Link to comment
Share on other sites

6 hours ago, Klassiker said:

The way I was taught (by trained watchmakers, but I myself am not qualified) was in line with what you are describing. In detail;

1. set the pallet fork against the left-hand banking pin. This ensures that the impulse jewel enters the fork.

2. introduce the balance assembly with the balance cock at least 90 degrees anticlockwise of its final position

3. seat the lower balance pivot without disturbing the pallet fork

4. rotate the balance cock clockwise (or the movement anticlockwise, whilst holding the cock still) into its final position, and rest gently on top of the balance wheel

5. locate the upper pivot in the jewel. The balance begins to swing

6. Drop the screw in. Hold the cock steady with a piece of pegwood or a toothpick and slowly tighten the screw.

7. If the balance stops swinging, immediately back off the screw.

I guess you could also reverse the directions described in steps 1 to 4. At no stage are you coiling or uncoiling the hairspring.

This is my process, although I've never looked to ensure pallet fork is to the left. Thanks for the detailed answer; it will make me better in the future.

Link to comment
Share on other sites

This is how I was taught. Movement in movement holder. Add a tiny amount of power.  Balance complete attached to balance cock. Balance cock held by tweezers, You need to get the impulse pin between the pallet forks, lower the cock in your tweezers between the forks. If you miss rotate the movement holder around until the impulse pin is between the forks, depending which side the pin is to the fork will depend which way you rotate.  Make sure the balance is home before you tighten up the screw.  

  • Like 3
Link to comment
Share on other sites

Always putting the fork in one direction would mean awkward installation for some movements. On a 7750 it would be installed with the cock over the movement and rotated outwards if the pallet is set to the left for example.  More intuitive way to do this without having to remember which direction to twist things for different movements would be to just flick the fork towards the inside if the movement and present the balance with cock pointed away from movement, then rotate it inward into position and fasten.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • in general this shouldn't be any change. but in general questions like this it be nice to know the specifics of the watch in other words how was it performing before it was cased up and what is it doing now.
    • just as a reminder this watch is a Swatch group product. This will bring up a problem like spare parts and technical information. that I found some links to some information on when I talk about your watch and some of the technical and basically your watch is equivalent to 2834-2 for which I'm attaching the technical sheets. But equivalent does not mean exactly the same you want to do a search on the group for C07 as we discussed this watch before including the technical differences how it's supposed to be regulated and basically because it's watch group there is no parts availability. https://calibercorner.com/eta-caliber-c07-xxx/   https://www.chrono24.com/magazine/eta-movements-from-the-2824-2-to-the-powermatic-80-p_80840/ https://www.watchuseek.com/threads/h-10-movement-details.4636991/ eta CT_2834-2_FDE_481857_15.pdf
    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
×
×
  • Create New...