Jump to content

My first! Omega 565 cal. Seamaster project

SiZi

By SiZi
in Your Walkthroughs and Techniques

 Share

Recommended Posts

SiZi Member

SiZi

Posted
Posted

I’m in the process of servicing my first watch ever, after completing two levels of Mark’s course. I welcome tips :)

So far I have disassembled and done one cleaning. Next, I will use the ultrasonic and then will lubricate and reassemble. Fingers crossed!

415B3FD1-3EB1-4465-8287-E4D33B525F48.jpeg

E2D611A9-6F52-4ECD-B82A-A131184ABE09.jpeg

Link to comment
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
SiZi Member

SiZi

Posted
  • Author
Posted
6 hours ago, Watchtime said:

really nice work for a 1st timer...well done...did you see Mark's comment about putting back the main spring by hand...:biggrin:

lol, yes, but it was too late! I didn’t have a wonder and wasn’t ready to wait several weeks for one to arrive (I live in India). So, this time won’t be best practice :)

Link to comment
Share on other sites
SiZi Member

SiZi

Posted
  • Author
Posted
6 hours ago, jackie01 said:

Congratulations. It's pleasant to see this work. Would you describe how you did cleaning process od the dial?

Thank you, and sure... first I used cotton buds to very gently wipe dirt off the dial face. Then, for the metal hour markers at 12,3,6,9 a little simichrome was used with a cotton bud. I had to be super gentle through the process. 

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted
On 9/9/2019 at 1:33 AM, SiZi said:

lol, yes, but it was too late! I didn’t have a wonder and wasn’t ready to wait several weeks for one to arrive (I live in India). So, this time won’t be best practice :)

Many people will disagree, but I find that it is ok to fit mainsprings by hand if you are careful. I still use a winder when it's easier though.

  • Like 1
Link to comment
Share on other sites
  • 2 years later...
JohnR725 Distinguished Member

JohnR725

Posted
Posted
On 9/8/2019 at 9:57 AM, SiZi said:

I managed to put the mainspring back by hand, and started assembling the watch.

A helpful tip for anyone looking at this discussion? I snipped out an image found up above a typical newbie mistake? People usually reassemble the watch in the opposite order they took apart. Usually what I'll notice is they put the pallet fork in right at the very beginning and that's a big mistake. Yes you can put it in but you don't have to. If you don't have the pallet fork in you can verify that the gear train spins. It makes it a lot easier to put the wheels back in if the pallet fork is not there. So typically you put it in just before you put the balance wheel in makes things a lot easier.

 

not the first part to go in definitely not.JPG

  • Like 3
  • Thanks 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
On 3/4/2022 at 4:44 PM, JohnR725 said:

A helpful tip for anyone looking at this discussion? I snipped out an image found up above a typical newbie mistake? People usually reassemble the watch in the opposite order they took apart. Usually what I'll notice is they put the pallet fork in right at the very beginning and that's a big mistake. Yes you can put it in but you don't have to. If you don't have the pallet fork in you can verify that the gear train spins. It makes it a lot easier to put the wheels back in if the pallet fork is not there. So typically you put it in just before you put the balance wheel in makes things a lot easier.

 

 

 This makes lots of sense.  When you have the fork in place and instal the barrel bridge next, you have missed the chance to verify the train running effortless and its back spin. 

Link to comment
Share on other sites
  • 1 month later...
jerryvs Member

jerryvs

Posted
Posted

my opinion for the correct reasembly 

1)barrel bridge 

2)train wheel bridge 

3) sec pinion with care a lot of 3rd wheels are damaged for this assembly 

personaly i take a new clear oiler to hold them down(the pinion) to put on the bridge 

4) pallet fork 

5) balance  

and good oiling and a bid of luck if you use the old mainspring 

 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • dnhb
      Is this a 'hack' ?

      By dnhb · Posted

      Showing state of hairspring on receipt, backplate & 'dished' wheel. 
    • mikepilk
      Setting lever spring

      By mikepilk · Posted

      I would harden and temper (to a light blue). It's so easy to do and only takes a couple of minutes. A search on ebay UK for "spring steel strip cs" finds plenty available in small quantites and thicknesses from 0.1mm up.  But the question is ( @nickelsilver) which "CS" number is best for watch parts ?  Also, from one of the ads : "CARBON SPRING STEEL. SIZE IS METRIC 15.00mm X 0.10mm X 304 MM  CS100 FINISH BRIGHT . HARDENED AND TEMPERD TO 480-530VPN" I've no idea about 480-530VPN. Does that mean it needs annealing before working?       Have you seen this video, he shows how to determine where the indents go ?  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      Here is the insert ring for rectangular or elliptical movements: Note that the length is the side with the stem cut out on the spreadsheet (in the picture below this is 15.15: Here is the fake pdf file, again you need to convert to .zip after download to access the FreeCAD and 3mf files. Rectangular insert disc.pdf    
    • JohnR725
      Omega cal. 565 - low amplitude

      By JohnR725 · Posted

      as you took the mainspring out what did it look like? It's amazing how much amplitude you can get if the mainspring actually has the proper shape. last week I was doing a 12 size Hamilton and was very much surprised with the beautiful back curvature the mainspring had. Then the watch had a really nice amplitude the group would be so proud it was 350 until I dropped the lift angle down to 38 that drop the amplitude quite a bit below 300. then with the beautiful back curve it still had really nice amplitude the next day. I really wish all my mainspring's look like this as the watch had beautiful amplitude the next day. So many of the aftermarket pocketwatch Springs I see now do not have anything resembling a back curve may be a slight curve and that's about all. They still work but they just don't work as nice as a properly made spring. then Omega as all sorts of nifty technical documentation unfortunately every single corner is watermarked with where it came from who downloaded it etc. very paranoid company. On the other hand I will snip out images like from the document on recycling a mainspring barrel. for instance here's the section on what your mainspring should look like. water damaged a lot of times means rust was there rust on this watch?
    • RichardHarris123
      Without Our Forum

      By RichardHarris123 · Posted

      I wondered that?
×
×
  • Create New...