Jump to content

My first! Omega 565 cal. Seamaster project

SiZi

By SiZi
in Your Walkthroughs and Techniques

 Share

Recommended Posts

SiZi Member

SiZi

Posted
Posted

I’m in the process of servicing my first watch ever, after completing two levels of Mark’s course. I welcome tips :)

So far I have disassembled and done one cleaning. Next, I will use the ultrasonic and then will lubricate and reassemble. Fingers crossed!

415B3FD1-3EB1-4465-8287-E4D33B525F48.jpeg

E2D611A9-6F52-4ECD-B82A-A131184ABE09.jpeg

Link to comment
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
SiZi Member

SiZi

Posted
  • Author
Posted
6 hours ago, Watchtime said:

really nice work for a 1st timer...well done...did you see Mark's comment about putting back the main spring by hand...:biggrin:

lol, yes, but it was too late! I didn’t have a wonder and wasn’t ready to wait several weeks for one to arrive (I live in India). So, this time won’t be best practice :)

Link to comment
Share on other sites
SiZi Member

SiZi

Posted
  • Author
Posted
6 hours ago, jackie01 said:

Congratulations. It's pleasant to see this work. Would you describe how you did cleaning process od the dial?

Thank you, and sure... first I used cotton buds to very gently wipe dirt off the dial face. Then, for the metal hour markers at 12,3,6,9 a little simichrome was used with a cotton bud. I had to be super gentle through the process. 

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted
On 9/9/2019 at 1:33 AM, SiZi said:

lol, yes, but it was too late! I didn’t have a wonder and wasn’t ready to wait several weeks for one to arrive (I live in India). So, this time won’t be best practice :)

Many people will disagree, but I find that it is ok to fit mainsprings by hand if you are careful. I still use a winder when it's easier though.

  • Like 1
Link to comment
Share on other sites
  • 2 years later...
JohnR725 Distinguished Member

JohnR725

Posted
Posted
On 9/8/2019 at 9:57 AM, SiZi said:

I managed to put the mainspring back by hand, and started assembling the watch.

A helpful tip for anyone looking at this discussion? I snipped out an image found up above a typical newbie mistake? People usually reassemble the watch in the opposite order they took apart. Usually what I'll notice is they put the pallet fork in right at the very beginning and that's a big mistake. Yes you can put it in but you don't have to. If you don't have the pallet fork in you can verify that the gear train spins. It makes it a lot easier to put the wheels back in if the pallet fork is not there. So typically you put it in just before you put the balance wheel in makes things a lot easier.

 

not the first part to go in definitely not.JPG

  • Like 3
  • Thanks 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
On 3/4/2022 at 4:44 PM, JohnR725 said:

A helpful tip for anyone looking at this discussion? I snipped out an image found up above a typical newbie mistake? People usually reassemble the watch in the opposite order they took apart. Usually what I'll notice is they put the pallet fork in right at the very beginning and that's a big mistake. Yes you can put it in but you don't have to. If you don't have the pallet fork in you can verify that the gear train spins. It makes it a lot easier to put the wheels back in if the pallet fork is not there. So typically you put it in just before you put the balance wheel in makes things a lot easier.

 

 

 This makes lots of sense.  When you have the fork in place and instal the barrel bridge next, you have missed the chance to verify the train running effortless and its back spin. 

Link to comment
Share on other sites
  • 1 month later...
jerryvs Member

jerryvs

Posted
Posted

my opinion for the correct reasembly 

1)barrel bridge 

2)train wheel bridge 

3) sec pinion with care a lot of 3rd wheels are damaged for this assembly 

personaly i take a new clear oiler to hold them down(the pinion) to put on the bridge 

4) pallet fork 

5) balance  

and good oiling and a bid of luck if you use the old mainspring 

 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is.
    • Malocchio
      What tools does ebay have to offer this week.

      By Malocchio · Posted

      I recently bought this but not on ebay. I figured if I want something Japanese I better check Japanese auction sites since these don't seem to pop up on ebay. I paid 83 € plus shipping & taxes. I think it was pretty reasonable for a complete set in good condition.
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Did you take the friction pinion off the large driving wheel and grease it? Although, now that I think about it, that shouldn't have any effect on the free running of the train if the friction pinion isn't interacting withe minute wheel/setting wheel...
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      I did in fact use Rodico to get the spring into general position and "hold" it there while I used a fine oiler to make subtle positional adjustments.
×
×
  • Create New...