Jump to content

My first! Omega 565 cal. Seamaster project

SiZi

By SiZi
in Your Walkthroughs and Techniques

 Share

Recommended Posts

SiZi Member

SiZi

Posted
Posted

I’m in the process of servicing my first watch ever, after completing two levels of Mark’s course. I welcome tips :)

So far I have disassembled and done one cleaning. Next, I will use the ultrasonic and then will lubricate and reassemble. Fingers crossed!

415B3FD1-3EB1-4465-8287-E4D33B525F48.jpeg

E2D611A9-6F52-4ECD-B82A-A131184ABE09.jpeg

Link to comment
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
SiZi Member

SiZi

Posted
  • Author
Posted
6 hours ago, Watchtime said:

really nice work for a 1st timer...well done...did you see Mark's comment about putting back the main spring by hand...:biggrin:

lol, yes, but it was too late! I didn’t have a wonder and wasn’t ready to wait several weeks for one to arrive (I live in India). So, this time won’t be best practice :)

Link to comment
Share on other sites
SiZi Member

SiZi

Posted
  • Author
Posted
6 hours ago, jackie01 said:

Congratulations. It's pleasant to see this work. Would you describe how you did cleaning process od the dial?

Thank you, and sure... first I used cotton buds to very gently wipe dirt off the dial face. Then, for the metal hour markers at 12,3,6,9 a little simichrome was used with a cotton bud. I had to be super gentle through the process. 

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted
On 9/9/2019 at 1:33 AM, SiZi said:

lol, yes, but it was too late! I didn’t have a wonder and wasn’t ready to wait several weeks for one to arrive (I live in India). So, this time won’t be best practice :)

Many people will disagree, but I find that it is ok to fit mainsprings by hand if you are careful. I still use a winder when it's easier though.

  • Like 1
Link to comment
Share on other sites
  • 2 years later...
JohnR725 Distinguished Member

JohnR725

Posted
Posted
On 9/8/2019 at 9:57 AM, SiZi said:

I managed to put the mainspring back by hand, and started assembling the watch.

A helpful tip for anyone looking at this discussion? I snipped out an image found up above a typical newbie mistake? People usually reassemble the watch in the opposite order they took apart. Usually what I'll notice is they put the pallet fork in right at the very beginning and that's a big mistake. Yes you can put it in but you don't have to. If you don't have the pallet fork in you can verify that the gear train spins. It makes it a lot easier to put the wheels back in if the pallet fork is not there. So typically you put it in just before you put the balance wheel in makes things a lot easier.

 

not the first part to go in definitely not.JPG

  • Like 3
  • Thanks 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
On 3/4/2022 at 4:44 PM, JohnR725 said:

A helpful tip for anyone looking at this discussion? I snipped out an image found up above a typical newbie mistake? People usually reassemble the watch in the opposite order they took apart. Usually what I'll notice is they put the pallet fork in right at the very beginning and that's a big mistake. Yes you can put it in but you don't have to. If you don't have the pallet fork in you can verify that the gear train spins. It makes it a lot easier to put the wheels back in if the pallet fork is not there. So typically you put it in just before you put the balance wheel in makes things a lot easier.

 

 

 This makes lots of sense.  When you have the fork in place and instal the barrel bridge next, you have missed the chance to verify the train running effortless and its back spin. 

Link to comment
Share on other sites
  • 1 month later...
jerryvs Member

jerryvs

Posted
Posted

my opinion for the correct reasembly 

1)barrel bridge 

2)train wheel bridge 

3) sec pinion with care a lot of 3rd wheels are damaged for this assembly 

personaly i take a new clear oiler to hold them down(the pinion) to put on the bridge 

4) pallet fork 

5) balance  

and good oiling and a bid of luck if you use the old mainspring 

 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Ok thanks Ross, I will give that a try!😁
    • rossjackson01
      Intro

      By rossjackson01 · Posted

      Welcome my friend. 
    • rossjackson01
      Help please.

      By rossjackson01 · Posted

      Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
×
×
  • Create New...