Jump to content

Perrelet James Cook Antarctica Restoration

manzana

By manzana
in Watch Repairs Help & Advice

 Share

Recommended Posts

manzana New Member

manzana

Posted
Posted

Hi,

I will be working on restoring Perrelet James Cook Antarctica. 

For those who may not know the brand, Perrelet takes its name from Abraham Louis Perrelet, the inventor of automatic watch movements back in late 1700. The brand, however, did not survive through the turbulent times, and was only re-activated in the 1990s. And that's when Perrelet James Cook Antarctica was born.

I would say that the Perrelet timepieces from the late 1990s and early 2000s seem to be the most beautiful to me. I think the case design and the dial are timeless, hence my personal affinity to the brand.

I already own a two-tone Perrelet Tempest and spotted this Perrelet Antarctica on eBay with some visible damage to the dial and hands. I pulled the trigger and here I am trying to restore it. Also, the bet with the size of the bracelet did not pay off, and I am currently trying to source spare links from Perrelet - what a pain. I already contacted the authorised distributors in the US, the UK and Germany, but apparently everyone in Switzerland is on holiday now!

 

917304224_s-l1600(3).thumb.jpg.1c8520451ecd2671931a2b087658480f.jpg

 

As you can see, the dial appears to be water damaged, but the markers are fine. Additionally, the front rotor (the trademark of Perrelet watches) appears to be discoloured in places, which after some inspection seems to be due to stripping of the nickel (or possibly gold) plating on steel rotor. I will be nickel plating soon (using brush technique) and will share pictures soon.

20190723_185254_HDR.thumb.jpg.682d37e460d5553a6e01cea2ee13eec8.jpg

 

I have managed to remove the markers and strip the dial from its colour. I am however unsure whether the original colour was achieved by chemical treatment or painting - the colour seemed to be completely resistant to varnish. It could only be removed by gentle polishing. There is still some left over in the ridges.

I am unsure how to proceed from here. I would like to get back the beautiful blue finish on the dial. I already purchased an airbrush, but I have difficulty in choosing the right paint for the job - I would like to preserve the sharp look of the ridges without putting too many thick coats. I would greatly welcome any advice on what paint would be the best for the job, and how to prep the dial (assume roughing slightly with 1500 sandpaper would do fine?)

Alternatively, is it possible to achieve such deep, aquamarine blue colour by electroplating? That would seem like an ideal solution?

20190801_180205.thumb.jpg.439b07f8e028fa4cb14bb5a5098eb317.jpg

 

Hopefully, all the sweat will pay off. I will keep updating the thread with progress as I go. Happy to answer any questions on my work so far.

  • Thanks 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

How about the movement, in house?

Much like ulysse Nardin the dial, color and design is a halmark of their pieces, and very attractive. Unfortunately I don,t know the first thing about coloring/ painting, just the movements. 

I follow your post with interest.

Best wishes.

 

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted

It is possible that the dial is dyed rather than painted. This technique is often used on anodiesd aluminium finishes.

Alternatively it may be a coloured lacquer (similar to nail polish) to give that transparent/metalic look. 

Whatever technique was used, there is probably also a sealing topcoat or clear coat to lock in the finish.

You will most likely need to experiment with scrap metal pieces till you get something you like.

Link to comment
Share on other sites
RyMoeller Super WRT Addict

RyMoeller

Posted
Posted

Interesting.  I've not even heard of the Perrelet watch brand until this very post but they have some cool timepieces- I like the "Turbine Family".

Often the color of a watch dial is achieved through a chemical process.  To repeat it you would need to know what metal is used for the substrate (brass, steel, aluminum, etc.) 

Anodizing also comes to mind because you can get some vivid really vivid colors.

  • Thanks 1
Link to comment
Share on other sites
  • 4 weeks later...
watchabit Member

watchabit

Posted
Posted

I have watched many a infomercial satellite feed in the 90's when they were selling these watches. Exuberantly hyped and sold with all the discounting and bundling techniques. I always felt they were pitched to those who didn't know better and at the time I think they were regarded as lower quality "pretty" watches. That said, I always was tempted to buy one but never did as I'd rather spend the money on a quality vintage watch.   

Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is. I've attached a lesson regarding mainsprings, focussing on the size and strength of the spring within the barrel, you might find helpful. Unfortunately it is a PDF converted from a PowerPoint presentation, but only a slide was lost that was originally a video of fitting a mainspring   Lesson 5 The mainspring.pdf
×
×
  • Create New...