Jump to content

Vintage wrist-watch crystals, simplifiable?


Recommended Posts

Greetings all.

Again I find myself in the middle of a rather difficult search for a vintage watch crystal. This, despite it being a round crystal, that should have some GS number that works. This is the second time that I have tried so very hard to order the right crystal the first time and failed. Close, but no cigar. It's also the second time that it is with a Girard-Perregaux wrist-watch that is probably from the late-forties to early fifties. And again it is with the type of case that utilizes a bezel that cinches down over the crystal, which should be a snug fit around the case bottom. I believe that Benrus used this type case, as well as some others.

I don't know if there's a way to do it, but it sure would be nice to start compiling a database that shows brands/types/sizes of cases along with their GS (or other brand) crystal. I realize that there are many types and sizes of vintage cases, but it would be a very convenient database. Perhaps like Dr. Ranfft's movement database? I'm sure it wasn't built in a day. I'm sure that I could add a few at this point. And if a lot of people add to it, it has the potential to save a lot of time and money for professionals and hobbyists alike. Make any practical sense to anyone? Many thanks.

 

Link to comment
Share on other sites

If your assembly is midcase with rehaut / plexi / bezel then you could the method I use.
1 - measure the outer diameter of the rehaut and the inner diameter of the bezel.
2 - search on cousinsuk a plexi with the closest profile, inner diameter a little too small for the rehaut and outer diameter a little too large for the bezel.
3 - gently sand with 2000 grade the inside diameter of the plexi until you can press it on the rehaut with a tight fit
4 - remove the plexi and gently sand with 2000 grade the outer diameter of the plexi until you can press it inside the rehaut with a tight fit
5 - clean everything
6 - put a tiny bit of grease on the rehaut to help and press the plexi back
7 - put a tiny bit of grease on the bezel and press it over the plexi with a crystal press
Using that method I got good results with even 6 ATM waterproofness.


Envoyé de mon moto g(7) power en utilisant Tapatalk

  • Like 1
Link to comment
Share on other sites

Thanks. I may end up doing something like that after I try at least one more. I got so close with the first one. Getting it right the first time seems very difficult with these cases. I'll insert an image of a watch that has the same waterproof design case. it's a ladies Perregaux in the old "Mermaid". It is like the forties and early fifties SeaHawks, but smaller. Thanks again for your suggestion. Cheers.

BTW: I found that a PA200 that is for a Wyler watch worked perfectly on this one. There's another GS PA crystal that is near the size I need, and is also said to be for a Wyler. I may end up trying that one. Maybe Wyler and GP were utilizing the same cases? Or maybe I was just lucky on the Mermaid?

 

MermaidWCrown.jpg

Edited by MrRoundel
Added "BTW"
Link to comment
Share on other sites

1 hour ago, MrRoundel said:

Thanks. I may end up doing something like that after I try at least one more. I got so close with the first one. Getting it right the first time seems very difficult with these cases. I'll insert an image of a watch that has the same waterproof design case. it's a ladies Perregaux in the old "Mermaid". It is like the forties and early fifties SeaHawks, but smaller. Thanks again for your suggestion. Cheers.

BTW: I found that a PA200 that is for a Wyler watch worked perfectly on this one. There's another GS PA crystal that is near the size I need, and is also said to be for a Wyler. I may end up trying that one. Maybe Wyler and GP were utilizing the same cases? Or maybe I was just lucky on the Mermaid?

 

MermaidWCrown.jpg

     that is a wyler style case, yes.  the wyler crystols are unique to this watch AND hard to find.  if you have a lathe,  cut an "aftermarket" crystol to the proper inside and out side to a "press fit" since it is the only thing that holds the watch together.  good luck.  vin

  • Like 1
Link to comment
Share on other sites

Thanks, vin. I appreciate your advice. Yes, the crystals need to be the proper ID, OD, and really thickness, in order to work. Very temperamental sizing. And yes, that's all that holds the case together. The one I chose would probably have worked, but the ID was slightly large, and didn't allow a strong enough cinching against the back. I THINK it would have worked if the ID was a touch smaller. I may try the Wyler to see if it might work.

I do have a lathe. What would I hold the crystal in while cutting? I have a bezel-chuck (Vintage WW style lathe.). Would that work? I don't have a three or four jaw. Thanks again. Cheers.

Edited by MrRoundel
Link to comment
Share on other sites

    I use 3 and 4 jaw chucks, large and small on a "compound lathe".   how does a " bezel - chuck" grab a crystol?  with a 4 jaw,  you invert the jaws and grab the inside so you can cut the outer diameter.   do they make chucks for jewelers lathes?   vin

  • Like 1
Link to comment
Share on other sites

As you can tell, vinn3, I have a lathe, but so far it's mostly been for decoration. :D I was visualizing the bezel-chuck, and was thinking it could be used by placing the crystal in the center, thereby using the bezel-chuck as a "jawed" chuck. My bad.

I do know that the 3-jaw is probably a must for lathe work. I just haven't stepped up to buy one yet. Someday. Until then I guess I'm stuck taking $10 stabs in the near darkness until I get the right size. At least it's not a customer-owned watch. Thanks again. Cheers.

Link to comment
Share on other sites

I just tried the fit of the PA370-10 as far as the OD holding the crystal snugly. It does. So the OD is good for the bezel, but the ID is too big for the case back. If the crystal held to the case-back, I think all would be good, as the snug fit would hold the crystal to the bezel well enough, methinks.

Rather than trying to modify a blank, or find the exact crystal, I am considering UV gluing the crystal to the case back. Since it will still be able to be pressed out from the bezel/lug part, it might work. The hang-up will be at some point down the line when I have to service the movement again. However, I might be able to be sparing enough, but strong enough, with the glue to be able to break it free and clean it up with acetone at that point. Comments? Thanks again.

 

Link to comment
Share on other sites

i have got a few of those "glued togethers".   its not cricket.   i have secured a loose crystol with 3 dots of epoxy  rather than smearing other glues all around.  i have a book on how to run a lathe i could post.   for the hobbist,  the UNOMAT  is not that expensive .   vin

Link to comment
Share on other sites

Thanks, vinn3. Hmm...Unimat. I forgot about those. I actually do have an SL1000 that I won in a raffle a couple of years ago. I bought the 3-jaw chuck for it. I didn't think of it because I heard that it wasn't considered precise enough for most watch-work. Crystal work is probably not what they're referring to.

So if the 3-jaw on the SL1000 would work, I might be able to do something. Still, I'm not sure of how to order a crystal of sufficient size and thickness to be of use.

Oh, and the epoxy idea sounds like something I could work as well. That way I would just have to break those beads/bonds, remove the movement, and then soak the back to remove the epoxy.

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello from the Mid-Atlantic United States. I've been in the hobby for a few months and have concluded that I will be staying in it for a while. I've started to get some proper tools and I am looking forward to developing some skills. My current goal is to get comfortable enough to service / repair some watches I've inherited from family members.  My current project is a Mentor pendent watch with a BF866 movement that belonged to my great aunt.
    • Success! The watch is working, albeit not perfectly. I need to install a new mainspring. It only runs about 16 hours. Still, it's my first cleaning and rebuild. I bought it from the original owner's son on eBay! The other one was bought at a flea market. I needed both to complete the project. The model with a seconds hand had soldered watch band pins and I couldn't drill tiny holes so I used the flea market Waldan, which was nearly a perfect match. I also replated the case with nickel, but the result was subpar. It's never as easy as it looks.
    • Thanks guys. It's a Seawolf 10ATM pre spring bezel. The case knife stressed me a bit, but eventually got it off and cleaned - nearly seventy years of grime.  Thanks.  Cheers John
    • Exactly. This is a pic of the hairspring I'm working on. My horizontal v vertical rates are all over the place. There is no discernible terminal curve. My problem is that the outer coil is (possibly) hitting the regulator pin. It's hard to tell but it looks to be getting very close. Also getting close to the stud, which could be @VWatchie's problem. You can see that I need to adjust the inner coil to centre the collet. That will hopefully solve the problem. But then I'll take the spring off and attach it to the cock to see how it looks.   I don't know if it's causing your problem @VWatchie, but I would say your inner coil looks like this  
    • Welcome to the forum.
×
×
  • Create New...