Jump to content

bureau desk


luiazazrambo

Recommended Posts

Hi fellow Clockmakers,

Would a bureau desk work as a clock/watchmaker desk? Not high enough (could be solved) or stable enough? I could fetch one of these from facebook around 30-40 pounds.

I like the idea because it would be more or less child and dustproof as you can close and lock the whole thing.

Best regards,
lui

b3_1.jpg

b3.jpg

b2.jpg

b1.jpg

Edited by luiazazrambo
Link to comment
Share on other sites

As OH says, comfort is of paramount importance, so leg room and bench height are key.

Other than that I would go for the roll top type rather than the hinged down type as you will have to clear the work area of the hinge down type before you can close it. Also the sides of the roll top desk double as a catch net for fliers.

Link to comment
Share on other sites

High percentage of folks 90% or more  suffer some sort of neck problem.

The least would be to raise the table high enough so you wont lean over the work piece, takes little of getting used to. Don,t send your eyes chasing the workpiece, bring the piece close to your eyes instead. Best position is sitting like when driving long distance, facing streight forward.

Also making it to a glove box so to contain flying parts be real nice. 

Best wishes.

 

Link to comment
Share on other sites

High percentage of folks 90% or more  suffer some sort of neck problem

I can vouch for that. When I was in my 40's I was told by a doctor I had wear and tear of the neck of a person in their 70's all due to bad posture. I have spondylosis of the neck.   I have to take daily medication to relieve the pain. 

I don't wish that on anyone. It ended my watch/clock making.  

Link to comment
Share on other sites

Hi   All advise given is wise and should be noted, also consider lightening the inside of any desk/work place so as to give good reflection of light. My workbench is covered in white lino tile, a pale green as per the bergeon mats etc.  as Marc says the roll top is probably the best option.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is.
    • I recently bought this but not on ebay. I figured if I want something Japanese I better check Japanese auction sites since these don't seem to pop up on ebay. I paid 83 € plus shipping & taxes. I think it was pretty reasonable for a complete set in good condition.
    • Did you take the friction pinion off the large driving wheel and grease it? Although, now that I think about it, that shouldn't have any effect on the free running of the train if the friction pinion isn't interacting withe minute wheel/setting wheel...
    • I did in fact use Rodico to get the spring into general position and "hold" it there while I used a fine oiler to make subtle positional adjustments.
×
×
  • Create New...