Jump to content

Old lucien picard

billys

By billys
in Your Watch Collection

 Share

Recommended Posts

AndyHull Distinguished Member

AndyHull

Posted
Posted (edited)

From what you can glean via Google, you can see that Lucien Piccard was a quality make, however I can't find anything online that resembles your particular watch. There is probably a good reason for that.

I would guess the watch really is 1940 to 1950 or thereabouts, but there is one minor issue, so far as I can tell, the Piccard should have two "c"s in it, so I suspect that you have a particularly interesting fake.

 

t6885n6svnijd5.jpg

If it were just the dial that was spelled with one "C" then I might give it the benefit of the doubt and say that it was a re-dial, but since the caliber also has Lucien Picard I can only assume this is because it 'aint gen-yew-wine. It probably isn't a recent fake either, but rather one created at that time.

The watch is probably worth $20 just for the curiosity value alone. I've seen quite a number of pseudo this and faux that, but not a Lucien Piccard (or rather Lucien Picard).

Someone with more expertise may chime in at this point and prove me wrong of course.

Edited by AndyHull
  • Like 1
  • Haha 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
5 hours ago, AndyHull said:

I would guess the watch really is 1940 to 1950 or thereabouts, but there is one minor issue, so far as I can tell, the Piccard should have two "c"s in it, so I suspect that you have a particularly interesting fake.

I don't think it's fake, but there must be a reason for that. Maybe they needed to use a different name for legal reasons, but didn't wanted to renounce it completely. Someone surely knows.

picard-2.jpg

picard-1.jpg

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted
4 hours ago, jdm said:

I don't think it's fake, but there must be a reason for that. Maybe they needed to use a different name for legal reasons, but didn't wanted to renounce it completely. Someone surely knows.

picard-2.jpg

picard-1.jpg

Hmmm that is interesting. Piccard on the caliber, but Picard on the dial. Curiouser and curiouser. In that case, I may be wrong. It may be a genuine fake, genuine Piccard, rather than a knock off fake.... if you get my drift. Time to do some research I think. 

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted

Wow...

oh-not-much-juet-oening-up-a-whole-new-c

I just did a little googleification on the subject of Licien Pic(c)ard. It seems there is quite a convoluted history there. The brand started life as a quality watch maker, and most of the output until around 1968 appears to remain reasonable quality. Things get a little "wooly" after that, with the recent history being a series of venture capital and shell companies trading on the once good  name, as is so often the case with the lesser Swiss brands. Around 2017 the name appears to have gone under for the umpteenth time, no doubt to re-appear in its latest zombie garb when some other brand leech acquires it. As to the different spellings, I didn't find anything so far, but given the rest of the brand's history, piccard,picard,picccard,piccccard, the choice is yours.  

  • Like 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
1 hour ago, yankeedog said:

There is that five letter word..

Looks like  HB115S, a German made.there is also a variant HB 115. 

 

1 hour ago, yankeedog said:

There is that five letter word...

Would you settle for albanian made?

Link to comment
Share on other sites
billys Member

billys

Posted
  • Author
Posted
On 7/10/2019 at 9:17 AM, vinn3 said:

    good score Bill ;     is it running,  is the balance staff good?   i noticed the screw heads have been "upset".   this is not a problem if the repairs are proper. good show, good luck.  vin

Yes its running good , keeping time. I dont think it is a fake. If i were making a fake i would not make the mistake of spelling

Link to comment
Share on other sites
  • 4 months later...
AndyHull Distinguished Member

AndyHull

Posted
Posted
On 12/9/2019 at 5:25 AM, Bauertime said:

Just wanted to say that Lucien Piccard makes the best looking movements by gold plating them. Just look up some for sale on the internet. I replaced an ETA 2512 with a Lucian Piccard movement for $25.00 that looks like should have cost a lot more.

You forgot to post the pictures ;~)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
    • Dell
      Broken lug

      By Dell · Posted

      Get someone local to tig it ,very easy fix and should only take a few minutes so probably wouldn’t cost much ,or failing that get it very clean and silver solder it. Dell
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, The winding pin is not split, well that's how it was when I obtained the watch. The movement is front-loaded and here's a picture of where the case screws are fitted. The face picture is before I dismantled it. Quick update.  I've always had a nylon ring sitting in the parts try that I wasn't sure where it went and left it to the last thing as I know it must be part of the case assembly. Anyway, looking at the picture in my last post you can see, just under the winding stem, a white-looking object, this is the nylon ring 🤭 So, I had to remove the dial again and replace the ring. Once this was all back together I placed the movement in the case and realized my initial problem maybe is not a problem as it looks like I can screw the movement back in the case and then place the hands as the dial is nearly flush with the outside of the case anyway so I'll be able to check for alignment. if all is good then just fit the crystal and bezel 🤔 I can't think of any issues with this approach but please comment if you think I've not thought of something. Another lesson learned as well. Take more pictures not just of the movement parts and location 😅
×
×
  • Create New...