Jump to content

can a 1970s TIMEX Marlin automatic be fixed?


Stu

Recommended Posts

Im new to watches and REally new to vintage watches but i picked up a 1977 Marlin for 10 bucks and it has a gorgeous dial so id like to get it fixed. I popped the back off and the movement isnt screwed in, its riveted in, so i dont know if even a watchmaker can fix it, nevermind for a reasonable price. The second hand doesnt move even when i shake it so it needs work. Id spend about 100 to get it fixed if its possible? Am i wasting my time trying to fix it?

Link to comment
Share on other sites

Hi Stu     You are not wasting time most watches can be fixed the site expert on TIMEX is jerseyMo,  Most timex were designed to be cleaned as is, remove dial and hands minding the dial washer and imerse in Naptha (lighter fuel) or alchol and leave on a kitchen towel to dry  then have another look. The conical pivots on the balance wear but can be reshaped and the balance pivot cups get gunged up stopping the watch.  I have enclosed the 1961 Timex manual in pdf some useful information in there.

timex 1961 service manual.pdf

  • Like 1
Link to comment
Share on other sites

  Stu;    welcome to the forum.   there is a complete timex forum, but it will be good to work on this one.   the earley ones were held together with screws - quite collectable.  you should read up or watch a video on "watch repair".    good luck.      vin

Link to comment
Share on other sites

12 hours ago, Stu said:

Id spend about 100 to get it fixed if its possible? Am i wasting my time trying to fix it?

I'd recommend that you check first what level of used working watch you can get for $100, that includes many nice Seiko and Swiss. Then later one as you have more experience you consider again what is worth spending money on and what is not.

Another way you could spend $100 a very nice basic tool set, that would allow you to ope watches, swap movement hands crystals etc. so start fixing by yourself.

Link to comment
Share on other sites

On 6/30/2019 at 1:27 AM, Stu said:

Im new to watches and REally new to vintage watches but i picked up a 1977 Marlin for 10 bucks and it has a gorgeous dial so id like to get it fixed. I popped the back off and the movement isnt screwed in, its riveted in, so i dont know if even a watchmaker can fix it, nevermind for a reasonable price. The second hand doesnt move even when i shake it so it needs work. Id spend about 100 to get it fixed if its possible? Am i wasting my time trying to fix it?

You might be able to do the job yourself, depending on your level of skill with a few simple tools, and a can of lighter fluid.
Timex watches are generally quite easily serviced. If it needs a repair however, then things might get a little more involved.

Perhaps take a look at this thread first.

Look also at the "Similar Content" related threads, and if you feel like giving it a go yourself, I'm sure there will be plenty of useful advice if you ask here.

Edited by AndyHull
  • Like 1
Link to comment
Share on other sites

On 7/1/2019 at 6:12 PM, AndyHull said:

You might be able to do the job yourself, depending on your level of skill with a few simple tools, and a can of lighter fluid.
Timex watches are generally quite easily serviced. If it needs a repair however, then things might get a little more involved.

Perhaps take a look at this thread first.

Look also at the "Similar Content" related threads, and if you feel like giving it a go yourself, I'm sure there will be plenty of useful advice if you ask here.

This is fantastic. I was just looking at the watch interior tonight, thinking i might be able to do something so this is very helpful. Thanks

Link to comment
Share on other sites

On 6/30/2019 at 6:34 AM, watchweasol said:

Hi Stu     You are not wasting time most watches can be fixed the site expert on TIMEX is jerseyMo,  Most timex were designed to be cleaned as is, remove dial and hands minding the dial washer and imerse in Naptha (lighter fuel) or alchol and leave on a kitchen towel to dry  then have another look. The conical pivots on the balance wear but can be reshaped and the balance pivot cups get gunged up stopping the watch.  I have enclosed the 1961 Timex manual in pdf some useful information in there.

timex 1961 service manual.pdf 1.73 MB · 7 downloads

im so glad i came to this site. Everyone has been incredibly helpful. Thank you!

Link to comment
Share on other sites

here is the shorten version of the "dunk and swish"

- dip movement (assuming you have already removed dial hands etc) in clear amonia  and soak for 15 minutes. tap container now and than to help loosen debris and oil grease. *** let ehe mainsrping down first ***

- rinse in cold water - dry out movment - a hair dryer is fine for this.

- dip movment in lighter fluid for 15 minutes. tap container now and than.

- dry out movement -

- dot pivots with syntheic watch oil -

- oil the end points of the balance - well this is a bit advanced and requires you to remove the balance cap.

- wind it up and flick the balance.... off she goes  "maybe"

What to do if she don't is the long version and lets not go there unless needed.

But before you do any of the above!!!!! look inside the movement for any damage such as a bent pallet fork, also once you let down the spring, try to wind it up agin to see if it holds tnsion. if the don't go no further cuz the spring is busted!  AND THAT IS A WHOLE NUTA LESSON :)

Oh there is a test, written essay 500 words mimimum  J\K

Hmm I think I'll call this the not so short but not the long version of the dunk and swish.  how about we call it the dunk and swish intermediate?

 

Edited by JerseyMo
  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thanks for the help guys! VWatchie I already found your thread but I'll check it again. Nice to know about acetone, I still have to get the shellac off since I made a little mess. I adjusted the jewel, put new shellac (the so called soldering technique, pallet tool too hot this time so the shellac "wire" melted in air before getting in contact with jewels or fork) rinsed the pallet fork and put it back dry. Amplitude is now in the 240-250 range that I expected in the first place. I guess there's enough oil in the escape wheel teeth already but I'll check that later. The mainspring was pretty beaten so a new one would probably boost the amplitude even further. Nice to learn new things. Now I have another thing to look for while disassembling. I wonder if the watch left the factory that way. 
    • Would be interesting to see it 🙂
    • These are all American movements (with the exception of the "Rubis"), and are all almost certainly "negative set" which means the stem is part of the case. So it's normal that they are all missing- they are with their cases. You will need male square bench keys to wind/disarm them. Vintagewatchstraps has a great writeup on the different systems. But basically, any American "x" size movement will fit any case for that size, possibly with some adjusting of the stem position. With Swiss movements, there is some interchangeability between calibers, usually within the same maker's range, but not really overall- there are thousands of different stems out there.
    • Hi, I'm very new to watchmaking and this is my first time posting here.  I've bought a lot of 10 vintage pocket watches size 0s from e-bay and just got them today.  Most of the balance wheels sprung quite freely and thus seemed like a worthy endeavor as a first batch for exploration.  I've just realized that none of them have any winding stems. Is there any way I could source appropriate winding stems for the movements? There seems to be assortments of various stems selling in bulk on aliexpress, but would any of them fit?  I've read on other threads that some people lathe their own stems (which is waaaay out of my current skill set, which is pretty much nil). Others say that you 'just have to try a few and see if they fit'. I would much appreciate any advice for this matter. Thanks!
    • Nice work.  In the last year, I have been servicing Accutron 218s.  I have the official Accutron hoder that provides electrical contact to the movement.  It is a pretty clever design.  There is a cut in the ring of the holder (shaped like a "C").  When in relaxed state, the holder is slightly smaller than the watch movement.  You spread the cut slightly and drop the movement in and release.  Very clean.  I have made 3D versions of this setup.  Have not explored using it generally for other movements.
×
×
  • Create New...