Jump to content

Damaged screw head

AlanSurry
 Share

Recommended Posts

AlanSurry Member

AlanSurry

Posted
Posted

Hi.  I picked up a fossil watch for a couple of pounds that hopefully only needs a battery, but one of the screws on the back is almost rounded off and doesn’t want to budge.  What’s the best way to deal with this?  The case is plastic so the screw is not rusted in.  I’ve resisted the temptation to put any sort of lubricant on it until I know what I’m doing.  Spa you suggestions would be gratefully received.  Thanks,  Al.  

43143669-C81B-471E-8FE3-78CE6699A493.jpeg

544ADD41-5AE3-4A87-8159-6D4D661145D3.jpeg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi  If the screw head is accesible try to cut a groouve in it with a fine knife edge  file to ceate a slot. Its not beyond some people to glue in a duff screw.  With a plastic case be very careful what you use to loosen the screw.  Be assured some body on the forum has had the same problem and will know of the way to proceed. good luck

Link to comment
Share on other sites
AlanSurry Member

AlanSurry

Posted
  • Author
Posted

Thank you for the reply.  Its a bit of an odd solution, but I wonder if anyone has tried solder to build up the screw or even soldering a screwdriver to the screw to gain grip.  I’ve got a colleague who can solder joints that I can barely see, so if it’s worth trying, I know just the man to ask.  Good idea, or not?  

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi  trying to solder a screw which is encased in plastic is frought with danger as the heat from the iron would cause the plastic to melt and worst case ruin the watch  proceed with extreeme caution if you follow that route. Another possible is to use a dremel and drill the screwhead off leaving a small stub to be removed with pliers

Link to comment
Share on other sites
AlanSurry Member

AlanSurry

Posted
  • Author
Posted

Thanks again for the replies.  I’d arrived at the “drill it out” solution but I’m still reluctant in case I can’t get the stub out.  I suppose, worse case it may end up with 3 screws holding the back on which isn’t the end of the world.  I hope it only needs a battery. Cheers.

Link to comment
Share on other sites
m1ks WRT Addict

m1ks

Posted
Posted

Being plastic it shouldn't be overly tight. You can try using a flat blade driver with a sharp edge to help provide the grip on the edges as you loosen.

If it won't budge at all then carefully and slowly grind the had with a dremel. This will leave a stub protruding once the back is removed which should come out easily.

In assuming you've loosened the other screws and confirmed it is screwed down and they're not moulded in cosmetic heads?

This often happens with fashion watches and they're a pop off case back.

  • Like 1
Link to comment
Share on other sites
  • 3 weeks later...
jdm Distinguished Member

jdm

Posted
Posted
13 minutes ago, mlfloyd1 said:

By some screw extractors from Esslinger.

A screw extractor may work (assuming it's a real screw) but is kind of pricey for an one-off job on a doubtful watch..

BTW Esslinger is an US seller.. I gather the OP is in the UK. 
 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Introduction

      By RichardHarris123 · Posted

      Hello and welcome from Leeds. 
    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
×
×
  • Create New...