Jump to content

Damaged screw head

AlanSurry
 Share

Recommended Posts

AlanSurry Member

AlanSurry

Posted
Posted

Hi.  I picked up a fossil watch for a couple of pounds that hopefully only needs a battery, but one of the screws on the back is almost rounded off and doesn’t want to budge.  What’s the best way to deal with this?  The case is plastic so the screw is not rusted in.  I’ve resisted the temptation to put any sort of lubricant on it until I know what I’m doing.  Spa you suggestions would be gratefully received.  Thanks,  Al.  

43143669-C81B-471E-8FE3-78CE6699A493.jpeg

544ADD41-5AE3-4A87-8159-6D4D661145D3.jpeg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi  If the screw head is accesible try to cut a groouve in it with a fine knife edge  file to ceate a slot. Its not beyond some people to glue in a duff screw.  With a plastic case be very careful what you use to loosen the screw.  Be assured some body on the forum has had the same problem and will know of the way to proceed. good luck

Link to comment
Share on other sites
AlanSurry Member

AlanSurry

Posted
  • Author
Posted

Thank you for the reply.  Its a bit of an odd solution, but I wonder if anyone has tried solder to build up the screw or even soldering a screwdriver to the screw to gain grip.  I’ve got a colleague who can solder joints that I can barely see, so if it’s worth trying, I know just the man to ask.  Good idea, or not?  

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi  trying to solder a screw which is encased in plastic is frought with danger as the heat from the iron would cause the plastic to melt and worst case ruin the watch  proceed with extreeme caution if you follow that route. Another possible is to use a dremel and drill the screwhead off leaving a small stub to be removed with pliers

Link to comment
Share on other sites
AlanSurry Member

AlanSurry

Posted
  • Author
Posted

Thanks again for the replies.  I’d arrived at the “drill it out” solution but I’m still reluctant in case I can’t get the stub out.  I suppose, worse case it may end up with 3 screws holding the back on which isn’t the end of the world.  I hope it only needs a battery. Cheers.

Link to comment
Share on other sites
m1ks WRT Addict

m1ks

Posted
Posted

Being plastic it shouldn't be overly tight. You can try using a flat blade driver with a sharp edge to help provide the grip on the edges as you loosen.

If it won't budge at all then carefully and slowly grind the had with a dremel. This will leave a stub protruding once the back is removed which should come out easily.

In assuming you've loosened the other screws and confirmed it is screwed down and they're not moulded in cosmetic heads?

This often happens with fashion watches and they're a pop off case back.

  • Like 1
Link to comment
Share on other sites
  • 3 weeks later...
jdm Distinguished Member

jdm

Posted
Posted
13 minutes ago, mlfloyd1 said:

By some screw extractors from Esslinger.

A screw extractor may work (assuming it's a real screw) but is kind of pricey for an one-off job on a doubtful watch..

BTW Esslinger is an US seller.. I gather the OP is in the UK. 
 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Endeavor
      Seiko 6139A & 6139B service manual WARNING !!

      By Endeavor · Posted

      The original 6139A manual is very clear in how to disassemble and how to assemble ...... step-by-step. However I haven't seen the 3169B manual, even the Japanese version around, which clearly highlights the difference in center-wheel.   6139A Seiko Technical Guide.pdf 6139_A.pdf 6139A.pdf 6139b.pdf        
    • watchweasol
      Seiko 6139A & 6139B service manual WARNING !!

      By watchweasol · Posted

      Hi as an addition a pertaining to the assembly of a 6319B  which will be handy for those working on this caliber Polly's 6139 guide.pdf 6139A.pdf 6139B.pdf
    • VWatchie
      Which Watch Have You Got Coming In The Mail ? Show Us !!!

      By VWatchie · Posted

      Casio MDV106G-1AV Gold DURO200 I'm going on a long family vacation to Southeast Asia this summer and wanted a cheap but reliable beater in case I lose it, break it, or get robbed. Quartz movements aren't my thing, but I'm not dogmatic and this was a cheap option. A few years ago you could buy it for under $50, but since this particular model with the Marlin fish has been discontinued, you have to pay about double that, but I still thought it was acceptable. Sure, I could wear one of my cheap and very reliable Vostok Amphibian divers watches, but I have a personal relationship with them (having put a lot of work into them) and don't want to risk losing them. Strangely, I feel very excited. Maybe because I haven't bought a brand-new watch in over 10 years! 😀 The only downside is that this is the watch Bill Gates has been seen wearing, and I'm not exactly a fanboy of Bill Gates. Anyway, who cares!?
    • Mercurial
      Incabloc Lyre Spring & Low Earth Orbit

      By Mercurial · Posted

      This post has some pictures that describe how to get the spring back into the setting without having to disassemble anything.  With patience, this approach works.  The advice that the spring will ‘float’ back in when positioned just right is spot on. If you try to push it so it flexes and pops back into the setting, it’ll probably just fly away, as you’ve already found.  Hope that helps, Mark
    • VWatchie
      Bench mat

      By VWatchie · Posted

      I recognize myself all too well. It takes a lot of experience and discipline to recognize when it's time to cancel and come back at a later time. Very well said! We should have a forum dedicated to this topic as it is critical to achieve success when working on watches. It's a lot more important than most other things related to watch repair. And yes, just a short break can make a world of difference!
×
×
  • Create New...