Jump to content

Elgin Shock Master

rduckwor
 Share

Recommended Posts

rduckwor WRT Addict

rduckwor

Posted
Posted (edited)

Early 60's Elgin 10K Shockmaster. I suppose one of their attempts at water proofing a watch (see the crystal and gasket in the second picture). The question is how to get the crown off (Its wobbly when pulled out to the set position and I am certain it contains a gasket) so I can remove the movement? Dis-assemble the keyless works in place so I can grab the stem and unscrew the crown?? Thanks.

SM1.jpg

SM2.jpg

Edited by rduckwor
Link to comment
Share on other sites
rduckwor WRT Addict

rduckwor

Posted
  • Author
Posted
37 minutes ago, oldhippy said:

No way will it come out from the back. Have you tried to pull the stem out? I'm thinking it might be a two piece stem. 

WINNER, WINNER, Chicken Dinner!  You and Gene Jockey, the resident Elgin guru over at WUS came up with the same answer.  I had hopes, but before stripped the entire stem out and ruined the movement, I needed confirmation from the experts.  You sir, are an expert, and a life-saver.  THANKS!!

 

RMD

Link to comment
Share on other sites
  • 1 month later...
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
On 6/26/2019 at 12:56 AM, rduckwor said:

WINNER, WINNER, Chicken Dinner!  You and Gene Jockey, the resident Elgin guru over at WUS came up with the same answer.  I had hopes, but before stripped the entire stem out and ruined the movement, I needed confirmation from the experts.  You sir, are an expert, and a life-saver.  THANKS!!

 

RMD

I don,t see how the movement is ruined that you say you did, anytime I see no obvious way to remove the stem, I think two piece stem. Never mind that, whoever is the winner can I have the chicken dinner?:bbq:

  • Haha 1
Link to comment
Share on other sites
yankeedog Distinguished Member

yankeedog

Posted
Posted

agreed on two piece stem. it's a sort of male female arrangement. tip up the movement  and rotate the crown . you will note that the movement wobbles up and down. When it wobbles to its highest spot the split in the stem will be perpendicular to the case and the movement will tilt out easily.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • JohnR725
      Omega cal. 565 - low amplitude

      By JohnR725 · Posted

      as you took the mainspring out what did it look like? It's amazing how much amplitude you can get if the mainspring actually has the proper shape. last week I was doing a 12 size Hamilton and was very much surprised with the beautiful back curvature the mainspring had. Then the watch had a really nice amplitude the group would be so proud it was 350 until I dropped the lift angle down to 38 that drop the amplitude quite a bit below 300. then with the beautiful back curve it still had really nice amplitude the next day. I really wish all my mainspring's look like this as the watch had beautiful amplitude the next day. So many of the aftermarket pocketwatch Springs I see now do not have anything resembling a back curve may be a slight curve and that's about all. They still work but they just don't work as nice as a properly made spring. then Omega as all sorts of nifty technical documentation unfortunately every single corner is watermarked with where it came from who downloaded it etc. very paranoid company. On the other hand I will snip out images like from the document on recycling a mainspring barrel. for instance here's the section on what your mainspring should look like. water damaged a lot of times means rust was there rust on this watch?
    • RichardHarris123
      Without Our Forum

      By RichardHarris123 · Posted

      I wondered that?
    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      I dont understand why a patreon membership would have limited places ??
    • clockboy
      Hi all

      By clockboy · Posted

      Welcome to the forum, enjoy. It’s highly unlikely you will be able to purchase a new bezel look on eBay for a pulsar watch for repair to find a bezel.
    • JohnR725
      Balance spring fell out of regulator pin.

      By JohnR725 · Posted

      just one little minor reminder here this isn't your normal balance wheel.  pages 17 and 18 are what you really want to be looking at. normally studs don't turn but this watch has the etachron system designed for lots of adjustment. Personally I would try to rotate the stud back to where it's supposed to be. If you're lucky you didn't actually bend it at the stud it just looks really bad as the stud has been rotated grossly out of position.. I think things will look a lot better if you put the hairspring back where it's supposed to be by rotating the stud. it's hard to tell if you actually did bend it at the stud or not we won't know until you rotate the stud back more or less where it's supposed to be. Then you want to pay attention to the manual of how to put the hairspring back in the regulator pins because yes they rotate also and they rotated specific directions otherwise bad things will happen to your hairspring. so initially you can open up the regulator as wide as it can go and don't worry about closing it until thing everything is right then you can close them a little bit
×
×
  • Create New...