Jump to content

I'm so sad with my MS cleaning/oiling results!


Recommended Posts

Yes I am sad. So far I have only serviced two mainsprings, but they ended to be worse than before.

I open the barrel of my Seiko 70xx watch, take the spring out carefully and then I use a piece of paper sinked on naphtha to clean the old oils. Then I use another piece of paper sinked on IPA to rinse the spring. And then a third piece of paper with some drops of 8200 to oil it.

I clean the barrel and arbor in the ultrasonic, also using naphtha and then IPA. Dry it properly and apply 4 drops of 8217 grease, in quarters.

Lastly I insert the spring into the barrel, manually, mount the arbor and close the barrel.

The problem is that althoug the watches run with these MS, they run only for a few hours after wearing them all day. The last watch I've serviced only runs for 4 or 5 hours, sometimes less than that, so I've replaced the barrel complete with an old one, not serviced, and now the problem is gone, so no doubt the fault is mine.

I guess the spring is slipping inside the barrel. Is 4 drops of 8217 too much? How do you oils mainsprings?

Link to comment
Share on other sites

I have problems with 7 series mainspring also . I only oil the barrel walls with 8217 very little. 

 

Same here. I have found if I use as much 8217 7 series as I do in a 6 series barrel I can’t get more than 3 or so turns before the spring slips. So I barely use any on these.

 

 

Sent from my iPad using Tapatalk

Link to comment
Share on other sites

maybe one needs a new MS, maybe the bridle lost it's hardness. 

Use the old MS instead, the one that works.

I don't think making the MS wall more rough is a good idea (in time)....

 

What is the amplitude of the watch when the MS slips?

 

  • Like 1
Link to comment
Share on other sites

Yes, roughing it lost me a bit as I don't see the point to doing it and oiling at the same time  It can be a technique of course, but I haven't heard of it before. The MS/barrel set was working before I put my hands on it :D

Next time I'll put just one drop of 8217 instead of four.

About the amplitude, I don't know, I do not have a timegrapher yet.

Link to comment
Share on other sites

 

First of all Seiko barrels where made so as not to be opened. You were supposed to replace the complete unit every (I think) 5 or 7 years. Now parts are become obsolete, it is common practise to clean and lubricate the mainspring.  If you can clean the all the barrel parts including the mainspring in your watch cleaning machine. Never stretch out the spring and clean it by hand. This can cause the spring to become weak. If you do not have a watch mainspring winder, you can put the spring back by hand. Use tissue paper so your fingers do not meet with the spring. If it is an auto you should use braking grease not oil on the spring and inside the barrel. The only place to use oil is where the arbor makes contact with the barrel.

Link to comment
Share on other sites

Thank you oldhippy, I basically comply with what you're saying. 70xx barrels complete are no longet available, so we have to open them, or I tought I had to open and clean it. Everything by hand, using gloves but no estrapada involved as I don't have one, but I've seen lots of videos doing it just by hand. I don't think I've bended the spring or damaged it, but of course it's always a possibility.

I've oiled the spring itself with Moebius 8200 grase, the barrel/arbor friction area with HP 1300 oil and the barrel wall with 8217 which is a braking grease. I want to keep trying servicing those springs, but I'm going to rest for a few weeks.

Link to comment
Share on other sites

On 6/14/2019 at 6:19 AM, oldhippy said:

 

First of all Seiko barrels where made so as not to be opened. You were supposed to replace the complete unit every (I think) 5 or 7 years. Now parts are become obsolete, it is common practise to clean and lubricate the mainspring.  If you can clean the all the barrel parts including the mainspring in your watch cleaning machine. Never stretch out the spring and clean it by hand. This can cause the spring to become weak. If you do not have a watch mainspring winder, you can put the spring back by hand. Use tissue paper so your fingers do not meet with the spring. If it is an auto you should use braking grease not oil on the spring and inside the barrel. The only place to use oil is where the arbor makes contact with the barrel.

 I work a lot on seikos and old hippy is right,  for the 70XX series you can buy the MS and barrel separate now and i have never seen them sold complete. but good servicing practice is to replace the MS, esp if its been 3+ years since the last service. breaking grease is a must, i only use 8217 on manual winds. kluber makes an excellent breaking grease but cost about $65 a worthy investment if plan on working on more automatics. I dont however agree with hippy on using breaking grease on the spring, i havent heard of this before and i would imagine could decrease your amplitude, but then again old hippy knows his stuff so i could be wrong here.

also i recommend using a MS winder for sure, you can easily warp an MS when hand winding it, and that could also cause a decrease in wind down time and amp. clean the mainspring with a dry cleaner or ultrasonic, the only time you should stretch is when applying the grease. as far as sanding goes never done it and never plan to but thats not to say it wont work.

Link to comment
Share on other sites

You need to have an idea of how much power is left in the mainspring.

Remove the rotor and 2nd intermediate winding gear (the one with the left-hand thread). Put a full wind on the ms using the screw on the ratchet wheel. Wind it until it slips the barrel wall, and continue until it is just about to slip again.. you may need to do this a few times to get a feel of when the ms will slip. Take note of the time and let the watch run down and take note of how many hours its run. Give it a shake and let it run down again in case its a bit of dirt in the train. An unwound mainspring should not tick more than 15 seconds or so.

Next use a screw driver on the ratchet wheel screw, hold it and lift the click  (you may need to backwind a bit), release the screwdriver and count how many turns of the ratchet wheel is left. Usually half a turn is about all there is if the watch has wound down. If there is a lot of pressure in the mainspring then you have a train problem. Be careful at this stage because if the ms has a lot of power it can slip, Do it in stages and release the click when your fingers cant maneuver further (you'll see what I mean).

If having wound the ms fully and the watch only runs for 4-5  hours but not much power is left in the ms then the mainspring is either wrongly installed, bad or incorrect.

Do you have a timegrapher? Personally I suspect the watch is out of beat, ie ticks and tocks don't balance.

Good luck!

Anilv

 

Link to comment
Share on other sites

Thank you anilv, I'll try what you propose.

Why do you think it's out of balance? I do not have a timegrapher yet, it,s my next purchase in a couple of months. I've tried the open souce application TG, but there's to much noise in my area so the readings were wrong, over 300º amplitude and 15 ms beat error, so nothing I can rely on.

Would an out of balance problem stop the watch after a few hours resting on a table?

Link to comment
Share on other sites

9 hours ago, anilv said:

You need to have an idea of how much power is left in the mainspring.

Remove the rotor and 2nd intermediate winding gear (the one with the left-hand thread). Put a full wind on the ms using the screw on the ratchet wheel. Wind it until it slips the barrel wall, and continue until it is just about to slip again.. you may need to do this a few times to get a feel of when the ms will slip. Take note of the time and let the watch run down and take note of how many hours its run. Give it a shake and let it run down again in case its a bit of dirt in the train. An unwound mainspring should not tick more than 15 seconds or so.

Next use a screw driver on the ratchet wheel screw, hold it and lift the click  (you may need to backwind a bit), release the screwdriver and count how many turns of the ratchet wheel is left. Usually half a turn is about all there is if the watch has wound down. If there is a lot of pressure in the mainspring then you have a train problem. Be careful at this stage because if the ms has a lot of power it can slip, Do it in stages and release the click when your fingers cant maneuver further (you'll see what I mean).

If having wound the ms fully and the watch only runs for 4-5  hours but not much power is left in the ms then the mainspring is either wrongly installed, bad or incorrect.

Do you have a timegrapher? Personally I suspect the watch is out of beat, ie ticks and tocks don't balance.

Good luck!

Anilv

 

This is worthy of a walk-through post. 

Link to comment
Share on other sites

7 hours ago, aac58 said:

Thank you anilv, I'll try what you propose.

Why do you think it's out of balance? I do not have a timegrapher yet, it,s my next purchase in a couple of months. I've tried the open souce application TG, but there's to much noise in my area so the readings were wrong, over 300º amplitude and 15 ms beat error, so nothing I can rely on.

Would an out of balance problem stop the watch after a few hours resting on a table?

Wrap the watch and the microphone in multiple layers of bubble wrap, it is a fairly efficient noises blocker.
I suspect that even a dedicated time grapher machine will struggle if there is a lot of ambient noise.

You could also fabricate a noise deadening chamber out of a wooden box lined with upholstery foam or bubble wrap.

If you want to get fancy, use this stuff.
 

https://www.ebay.co.uk/itm/Pyramids-Foam-Self-Adhesive-Insulation-Accoustic-Hifi-Sound-Insulation/143236451168?hash=item21598ecb60:g:JvQAAOSwerdamIOT

 

s-l500.png

Edited by AndyHull
Link to comment
Share on other sites

I just rebuilt a 7002A this weekend.  I was very careful with cleaning/oiling, fitted a new mainspring and used a few dots of 8213 on the barrel. 

The gear train, balance are as free as they could be - amplitude about 235 deg DU/DD.

Seems about typical for the few Seiko's I have. I know they have low amplitudes, so I'm happy as it is.

Link to comment
Share on other sites

A balance which is out of beat will have an imbalance.. If it is out of balance the hairspring may not have sufficient power to pull the balance back. There are technical terms but in essence the ms forces the balance in one direction and the hairspring pulls it back in the other. Even if the watch is out of beat, a full mspring may get it to work for a few hours but once power tails off then it will stop.

You can install the complete balance in a bare mainplate and see if the impulse jewel (below the balance) is centred. This will be a good starting point and the watch should run well enough to be regulated by the rate adjuster (+/-).

One app I use is wildspectra .. available for android. Not as good as a timegrapher but enough to see the beat and rate. Note that even a running fan in the next room will affect the reading so its essential to have a quiet environment or source a hi powered microphone.

Good luck.

Anilv

Link to comment
Share on other sites

One way to check if the watch is in beat is to wind the ratchet wheel slightly, less than a quarter turn. Stop the balance if it is turning. Swing the balance a bit in one direction (around 5-10 degrees to start with), if it starts thats good. Now stop the balance again. Now swing it in the other direction the same amount. What you're aiming for is for the balance to start running if the balance is nudged the same amount in either direction.

On some movements you can also eyeball the pallet fork movement, it should be at rest in the middle of its travel when the balance is at rest. This is not so easy on the 7xxx series.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Yes, I do have the Seitz pivot gauge which is worth a small fortune these days. Got mine for about £200 which I thought to be crazy expensive at the time, but I've now seen asking prices over twice that. And no, I do not have the scaled pin gauge, but it would be convenient. Let me know if you find them! Anyway, the Seitz pivot gauge is in my opinion not really necessary if you have the JKA Feintaster. It can measure even the very small pivots w/o making any dents. One will have to be a lot more careful when using the Bergeon micrometres.
    • Update. Ran into a winding problem since some desperate previous repair guy had fitted the wrong winding gear. Cousins had one ! Turns out the movement is the slightly different 022 - 18 Looks like the one LH screw fixing for the crown wheel got updated to the two screw style.
    • Didn't you see the impact on your time machine? 🙂 Nobody told me this / or read it in any books but whenever I have a reading like yours one of the first things I check is the plate screws and in the majority of the cases the readings get better after tightening them, smoothing out your curves. If they are tighten enough it makes no sense to tighten them more as it brings no benefit but excessive force might cause the screwheads to brake off. You have the feel for it after a while. I have seen cases where the plate screws were not tight on purpose just to sort out some end shake issues but needless to say that's not the right way to go. Plate screws must be tight enough  just like the critical screws in automotive otherwise you screw up the whole movement in my opinion. I must stress that this is only my own opinion and i am just a hobbyist. 
    • I remember when I was in school the instructor would use whale oil on some problematic little tiny ladies watches because he felt it was a better oil. then for my birthday on my friends gave me a bottle of vintage nye watch oil. Complete with the advertisement inside which I have scanned below and what I find interesting is it hasn't gone bad in the model and it is super super thin I'm guessing the viscosity of water basically. then somewhere in the discussion group within the last year or so somebody purchased one of these bottles off of eBay and was using it on their watch. After all a bottle watch oil is? Apparently it was an expensive I'm guessing or it's what they had or something no idea what the final outcome was other than I found it amusing. then somewhere in the Internet somewhat it made up this interesting chart down below. I believe the first natural oil is there 8000 oil. Notice the friction properties in the first two columns in other words it's really good at reducing friction better than anything else.  But it does have additional specifications like contact angle which is almost never found in any spec sheet which has to do with how likely it is to spread. Big numbers are bad in those two columns and you can see spreading test it's very bad. So basically it's a really outstanding oil for a short period of time before it spreads away and of course being natural it has a habit of probably going bad very soon the best oil of course is Elgin oil at least the second version of their oil very good at reducing friction and very good at staying wherever you place it and still very fluid oil viscosity wise. then one of the most famous oils of all Swiss 9010 that I personally don't like and don't use quite a ways down on the chart personally prefer 9020 which unfortunately is not listed on this chart. It slightly heavier viscosity and has a little nicer contact angle those more likely to stay wherever you put it versus 9010 which universally requires epilam if you would like to stay wherever you putting it. then if you're in the viscosities here's an interesting chart that I found on the discussion group. ou will note there some minor variations between the viscosities listed here and the chart up above which may be attributed to the difference in temperature  universally everything is supposed to be at 20° C and the chart up above is at 40° C. Because what becomes interesting on the chart is 8000 is listed out of viscosity of 95 which does agree with their technical information and the PDF for the oil lists at 40° it is 41 where up above the chart everything is either listed as 50 or light whatever that means? Then Elgin oil is listed on the chart in a clever interesting way. you look on the chart at a viscosity of 125 you'll find Dr. Tillwich LGN oil which is the synthetic version of Elgin oil. Many years ago they had a request and gathered up a whole bunch of samples and synthesize the oil and for a while it was available for sale although it was rather expensive I had seen a bottle for about $100. and as far as viscosities go it does appear to be right in both charts in other words at 20° it's 125 and at 40° it's 50. So unfortunately it brings up the problem of viscosity or better yet contact angle determines the spread ability of your lubrication unfortunately we typically don't get contact angle we just get viscosity. So the casual trend is a heavier oil tends to not spread although as we can see from looking at the chart that isn't hundred percent true. As far as reducing friction goes viscosity doesn't necessarily come into play here either. Or basically we don't have enough of the right tech sheets to make a real proper comparison.
    • Somewhere in the back of my mind i thought you had the jewelled seitz pivot gauge, i was just asking if you had this scaled pin gauge as well. I might have just made up that thought  H. 😅
×
×
  • Create New...