Jump to content
  • Similar Content

    • By jackie01
      Hello guys,
      I want to show you my lately restoration project. This time it was a Seiko 7015-8000 with blue dial. Watch came to me in very poor condition. As you can see on photos the case was scratchty, crystal was totaly tarnished with deep scratches. Everywhere was dirt, gunk and mud...yuck. Movement was running and stopping with very low amplitude. After opened the caseback I wasn't suprised - it looked like as case - dirt and signs of wear. Rotor was loose and fall out the case. When I take off the crystall I saw dial which had faded Seiko logo, some scratches and hands which lost their lume.
       














       
      Next step was strip down the movement - everywhere dirt and dry old oil. Time to cleaning bath

       







       
      Look at this - it's my temporary balance wheel stand - I suspect that from temporary it will be permanent. It does job well.
       

       
      After cleaning it's time to assembly movement. Now it looks better - maybe not pristine but clean and shiny. New oil here and there and movement starts to run. Now it's time for bench testing before install it to the case.
       





       
       
      Meanwhile I took care of the case, dial and hands. Case got some polishing work - not to much cause I didn't want to loose the sharpness of edges. That is effect:
       





      Dial and hands got new lume - I am not perfect in this work but I still learn to do this. Additional the seconds hand was repainted to orange color. I didn't change the crystall but i just polished it with waterpaper and on the end polish paste. Effect suprissed me. Time for the  pleasant work - putting this all pieces together into the watch.
       







       

      VID_20190927_195610.mp4
       
    • By jackie01
      Hello,
      I started new project - Citizen 67-9119. It's seventies chronograph based on 8110A movement. Watch came to me as "fully working in great condition" As you can see there isn't crystal. The one which was here had chip and wasn't set properly in bezel so when i turned the watch it fall on the floor and broke. As you can see dial is in quite good condition, only it needs to be relumed. Hands needs to be repainted and relumed too. Movement works well but it is too speedy (  +3 min/24h). Chrono buttons work properly, only the hour counter stops at "3h" position so I must to take a look here. I striped down the watch and disassembled movement. There was some much oil everywhere so the cleaning is required. 















       
       
       
    • By jackie01
      Hello everybody,

      I open this thread to archive works on Citizen 8110A Bullhead. I purchased this watch in poor condition as You can see on the photos.


      Cause I have serviced few chronographs in the past I decide to try restore this watch. Maybe is not ractional from the economical aspect but we do this because we love it So let's open it.

      Hands are in good condition (required repaint and relume) but the dial has broken legs and tachy scale is faded :/ I think it's really hard to find orginal and there is no gold aftermarket replacement - sad. Look at the movement.







       
      Gosh, what a dirty place It needs good cleaning and oiling. 
      But the biggest problems are this.


       
      Broken post on main spring bridge and missing rocking bar core and screw in gear train. I need to find replacement.

      While I'll be working on movement the case and pushers are send to renew - putting new gold plated coat

       

      Stay tuned
       
       
    • By adsterb
      Hey everyone, I cant find out how to get this drown off and I've tried everything. The Miyota JS25 movement says PUSH and points to a hole which I've learned means this is where you press to reease the crown but I still can't get the crown out no matter which position the crown is in. I first tried with the crown all the way out then with it halfway in, then all the way in and haven't been able to get it out, please help.


    • By Calvin
      Hello guys..
      Why my seiko speedtimer 7015 chronograph run smoothly when its day(morning till evening)
      But its stop and heavy when its time to changing the day date,whats the problem and how to fix it..
      Thankyiuu
  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • Absolutely - thats the one. So far I have had a few issues with it but noting major. The gib in the compound slide was bent - easy fix but I need maybe add a couple more gib screws to make it more smooth and it came with an extraordinary amount of grit on the lead screws and ways. This is common with chinese lathes I think but didn't expect it with "German quality" - lesson learned I would like to install a thrust bearing too, to minimise  backlash. But the parts I have made so far are quite accurate not bad for a light duty lathe. Not unhappy.   There you go Sent from my SM-G950F using Tapatalk  
    • Hi folks, I have always liked watches - always had one on my wrist since I was a kid (over 40 years ago!).  However, I really just started considering watches as a hobby as I am now fascinated by automatic/manual wind movements.  I am very mechanically adept and love figuring things out, so I feel watches would be a natural extension of what interests me. My goal is to learn all I can as see where the journey takes me. I have some inherited watches that I would love to be able to service/get running - eventually.  Excited to learn!!  - Erik J.
    • Military watch ? War time vintage?God only knows what stories it could tell. What it is telling me now, is that it is a well serviced , well worn watch.Speaking as an old Grunt, I would tell you that we don't like to be poked any more than is necessary.
    • So I have to know, was it the caffeine, or did you stand too close to the microwave oven? Well done.
    • Hi and welcome to the happy factory Watchfellow 
×
×
  • Create New...