Jump to content
  • Similar Content

    • By jackie01
      Hello guys,
      I want to show you my lately restoration project. This time it was a Seiko 7015-8000 with blue dial. Watch came to me in very poor condition. As you can see on photos the case was scratchty, crystal was totaly tarnished with deep scratches. Everywhere was dirt, gunk and mud...yuck. Movement was running and stopping with very low amplitude. After opened the caseback I wasn't suprised - it looked like as case - dirt and signs of wear. Rotor was loose and fall out the case. When I take off the crystall I saw dial which had faded Seiko logo, some scratches and hands which lost their lume.
       














       
      Next step was strip down the movement - everywhere dirt and dry old oil. Time to cleaning bath

       







       
      Look at this - it's my temporary balance wheel stand - I suspect that from temporary it will be permanent. It does job well.
       

       
      After cleaning it's time to assembly movement. Now it looks better - maybe not pristine but clean and shiny. New oil here and there and movement starts to run. Now it's time for bench testing before install it to the case.
       





       
       
      Meanwhile I took care of the case, dial and hands. Case got some polishing work - not to much cause I didn't want to loose the sharpness of edges. That is effect:
       





      Dial and hands got new lume - I am not perfect in this work but I still learn to do this. Additional the seconds hand was repainted to orange color. I didn't change the crystall but i just polished it with waterpaper and on the end polish paste. Effect suprissed me. Time for the  pleasant work - putting this all pieces together into the watch.
       







       

      VID_20190927_195610.mp4
       
    • By jackie01
      Hello,
      I started new project - Citizen 67-9119. It's seventies chronograph based on 8110A movement. Watch came to me as "fully working in great condition" As you can see there isn't crystal. The one which was here had chip and wasn't set properly in bezel so when i turned the watch it fall on the floor and broke. As you can see dial is in quite good condition, only it needs to be relumed. Hands needs to be repainted and relumed too. Movement works well but it is too speedy (  +3 min/24h). Chrono buttons work properly, only the hour counter stops at "3h" position so I must to take a look here. I striped down the watch and disassembled movement. There was some much oil everywhere so the cleaning is required. 















       
       
       
    • By jackie01
      Hello everybody,

      I open this thread to archive works on Citizen 8110A Bullhead. I purchased this watch in poor condition as You can see on the photos.


      Cause I have serviced few chronographs in the past I decide to try restore this watch. Maybe is not ractional from the economical aspect but we do this because we love it So let's open it.

      Hands are in good condition (required repaint and relume) but the dial has broken legs and tachy scale is faded :/ I think it's really hard to find orginal and there is no gold aftermarket replacement - sad. Look at the movement.







       
      Gosh, what a dirty place It needs good cleaning and oiling. 
      But the biggest problems are this.


       
      Broken post on main spring bridge and missing rocking bar core and screw in gear train. I need to find replacement.

      While I'll be working on movement the case and pushers are send to renew - putting new gold plated coat

       

      Stay tuned
       
       
    • By adsterb
      Hey everyone, I cant find out how to get this drown off and I've tried everything. The Miyota JS25 movement says PUSH and points to a hole which I've learned means this is where you press to reease the crown but I still can't get the crown out no matter which position the crown is in. I first tried with the crown all the way out then with it halfway in, then all the way in and haven't been able to get it out, please help.


    • By Calvin
      Hello guys..
      Why my seiko speedtimer 7015 chronograph run smoothly when its day(morning till evening)
      But its stop and heavy when its time to changing the day date,whats the problem and how to fix it..
      Thankyiuu
  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • In theory you can work ruby with anything harder or as hard (diamond is worked with diamond), but it's so easy and cheap to get diamond lapping compounds and powders that it's really the way to go. I'd suggest a copper lap rotated in the lathe, but almost any material is ok- acrylic, iron, etc. For pallet faces I would use 1micron diamond, it will cut slowly but surely and leave an entirely satisfactory finish.
    • I picked this little Russian up and was enamored by the dial. When it arrived I discovered it had the stout Vostok 2209 movement. I found it was a very clean movement and only needed to be adjust for timing just a bit. The dial that had my attention looked to be silver plated copper with a rather dirty looking patina. The dial isn't engraved as I had hoped, but was stamped with the pattern formed during that process. I wanted to make that pattern pop so I painted the entire dial flat black and used thinner to remove paint only from the top surfaces. Was a bit tricky to accomplish but I think it came out great. Next I turned my attention to the hands. Somene had put a shiny black varnish on the hands as contrast, no lume was present. So I cleaned that of and since I didn't have any white paint, I used liquid white out. I know this is probably blasphemous, but it's a totally temporary solution until I get some lume I like. Placing the hands back on was a bit tricky as the fit was incredibly tight and tough to accomplish with my  huge sausage fingers. I have a black leather strap on order for it. Very pleased with the results. Thank you for reading this.  
    • Only had a 963...Look the same but not sure it is compatible? 
    • May I suggest that you are extremely careful in handling the piece, like zero forcing of anything ever, no free runs of the train under MS power, etc. Chinese mov'ts are especially delicate, they tend to break by themselves easily and do not resist any mistreatment. Very recently I have broken a Shangai one in three different parts, that before counting the rotor that had split in two and the anti-shock spring that left on a shock. A Segull can be just $60 but a Sellita 200 for GBP at 140+VAT is not that far way in terms of price, but deliver much better reliability, and the parts are actually available.
    • I must say these Chinese clones are getting very good indeed. The build quality may not reach the same standards but for hobbyist / amateur they seem remarkable value.
×
×
  • Create New...